Omega C4EIT/-EIT manual Figure I-2 Device-to-Device Communication, Remote iSeries -EIT/-C4EIT

Page 63

Appendix I Remote Access (Tunneling) (continued)

Figure I-2 Device-to-Device Communication

In order to use this Tunneling feature, some settings are required within the local and remote iServer’s.

I-1 Remote iSeries -EIT/-C4EIT

It’s recommended to configure the Remote iServer and have it up and running before the Local iServer is configured.

1.A static IP address must be assigned to the Remote iServer. This means that the DHCP must remain disabled.

Refer to the DHCP section of the user’s manual for details.

2.Use a browser to access the Remote iServer’s WEB page. Simply type the iServer’s IP address at the browser’s URL location (i.e. 192.168.1.50) followed by an Enter key. You should then see the iServer’s main WEB page.

3.Click on the OK button after entering the LOGIN password.

4.On the SERIAL page, under Serial Port section (see Figure 4.6 or 4.7) make sure the parameters: Baud Rate, Data Bits, Parity, Stop Bits, and Flow Control match the serial communication settings of your attached serial device.

5.Under Packing Techniques section (see Figure 4.8) make sure to set the End Character (Hex) to 00 and the Buffering Time is set to 0.

6.If Data is too fast, try setting the iSeries-EIT in continuous mode to 0-500 ms, so that the local connection has time to respond.

6.Click on Save button for the changes to take place.

Make sure that the serial cable and communication settings between the iServer and the serial device are valid.

57

Image 63

Contents User’s Guide Page Dhcp DNS Table of ContentsList of Figures ARP Commands and Responses IServer DiagnosticsAssigning an IP Address using iConnect Accessing the iServer’s HomeTable K-1 Data Transmission Characteristics RS485ILog Error Messages List of TablesBefore You Begin TIPEMC Considerations Part IntroductionDescription Accessing Devices Over the EthernetPart Hardware Physical Characteristics and MountingSerial Communication Interfaces For Models with -C4EIT Network Communication Interface SectionHalf Duplex Hookup Pin# ISeries Wiring Master/Slave Units via RS485 InterfaceNetwork Communication Interfaces 1 10BASE-T RJ-45 Pinout RJ-45 Pinout Connecting iServer to PC/Hub/Switch/RouterPart Network Configuration Network ProtocolsEthernet MAC Address Dhcp DNSIP Address Example C\Telnet 192.168.1.200 Serial Interface Configuration Communication Protocol Command Prefix LettersPart Operations LSB MSB Pinging the iServer from a DOS Prompt Default IP AddressIServer Login Access and Configuration Using a Web Browser4a iServer -C4EIT Overview OverviewIServer Network Network IServer Serial Page RS485 Serial Port IServer Serial Page Network to Serial IServer Serial Page Packing Techniques IServer Serial Page Multi-Host Connection 10 iServer Configuration Page Ethernet Configuration Date and Time 11 iServer Management Page Email, Snmp Management Email Snmp 12 iServer Management Page Alarm AT&T 13 iServer Security 14 iServer Device Query 15 iServer Device Setup Page RS485 -C4EIT Device Setup -C4EIT16 iServer Device Parameters Page -C4EIT 17 iServer Device Setup Page -EIT 18 iServer Device Parameters Page -EIT Device Parameters -EITReadings Device Setpoints Readings21 iServer Terminal Terminal22 iServer System System23 iServer Diagnostics Page 4.5.12.1 Diagnostics Serial Port DiagnosticsDiagnostics Ping Diagnostics Ethernet PortSerial Interface -C4EIT Part SpecificationsTime-Lag, IEC 127-3 recognized Serial Interface Network InterfaceTransients Overvoltage Surge 1.2 / 50uS pulse Electrical Safety EN61010-12001Part Measurement CategoryAppendix Aglossary Appendix B IP Address Class C Appendix C IP NetmaskMask Dotted Notation Mask Binary Mask Bits Class a Class BAppendix D Ascii Chart Dec Hex BinaryDec Hex Binary Char No Parity No parity Dec Hex Ctrl Key Definition Char Equiv Appendix D Ascii Chart ContinuationAscii Control Codes Dec Hex Ctrl Key DefinitionAppendix E IConnect Software Figure E-1 Assigning an IP Address using iConnectFigure E-2 Accessing the iServer’s Home Communication interface skip for embedded ethernet -EIT Appendix F HTTPget Program\iServerhttpget -r -S *02X01\r 192.168.1.2002000 \iServerhttpget -r -S *02X01\r Network read timeoutArp -g ﬁ Same as arp -a 192.168.1.96Appendix G ARP Program Appendix H Telnet Setup Admin PortISeries? Figure H-3 Telnet Setup iServer Help Figure I-1b Serial Tunneling iSeries -EIT Figure I-1a Serial Tunneling iSeries -C4EITRemote iSeries -EIT/-C4EIT Figure I-2 Device-to-Device CommunicationLocal iSeries -EIT/-C4EIT Figure I-3 Serial Multi-Host Connection -C4EIT Tunneling Troubleshooting IPORT, COM Port Redirector IPORT OverviewAppendix J IPORT Figure J-2a Redirect Serial Connection Figure J-3 iPORT Main Window IPORT Configurations Appendix K ILog Software Figure K-1 iLog Software Logging Data for an iSeriesISeries Wireless DevicesTable K-1 iLog Excel Applications Networked Product ILOG File AlternateTable K-2 iLog Error Messages Error # Description Page Page Page Page Page WARRANTY/DISCLAIMER Shop on line at omega.com