Omega Engineering OME-PIO-D96 manual OME-DB-24R/24RD Relay Board

Page 21

2.6.6OME-DB-24R/24RD Relay Board

The OME-DB-24R, 24 channel relay output board, consists of 24 form C relays for efficient switch of load by programmed control. The relays are energized by apply 12V/24V signal to the appropriated relay channel on the 50-pin flat connector. There are 24 enunciator LEDs for each relay and they light when their associated relay is activated.

Form C Relay

50Pin cable

OME-PIO-D96

Normal Open

Normal Close

Com.

OME-DB-24R

Note:

Channel : 24 Form C Relays

Relay : Switching up to 0.5A at 110ACV or 1A at 24DCV

	OME-DB-24R			OME-DB-24RD
50-pin flat-cable header	Yes			Yes
D-sub 37-pin header	No			Yes
Other specifications			Same

OME-DB-24R, OME-DB-24RD		24*Relay (120V, 0.5A)
OME-DB-24PR, OME-DB-24PRD		24* Power Relay (250V, 5A)
OME-DB-24POR		24*Photo MOS Relay (350V, 01.A)
OME-DB-24SSR		24*SSR (250VAC, 4A)
OME-DB-24C		24*O.C. (30V, 100 mA)
OME-DB-16P8R		16Relay (120V, 0.5A) + 8isolated inputs
OME-PIO-D96 User Manual (Ver.1.1, Mar/2003)			---- 19

Image 21

Contents User’sGuide Mexico CanadaBenelux Czech RepublicOME-PIO-D96 Table of Contents Introduction FeaturesSpecifications Order DescriptionOptions PCI Data Acquisition Family Product Check ListOME-PISO-series cost-effective generation, isolated cards Board Layout Hardware configurationEnable I/O Operation I/O port LocationRefer to DEMO1.C for demo program D/I/O Architecture Make sure the initial level is High or Low Interrupt OperationINTCHAN3 Interrupt Block Diagram of OME-PIO-D96INTCHAN0/1/2/3 COUNTL++ Initialhigh, activelow Interrupt sourceInitiallow, activehigh Interrupt source Muliti Interrupt Source Read all interrupt state OME-DB-37 Daughter BoardsOME-DN-37 & OME-DN-50 OME-DB-8125OME-ADP-37/PCI & OME-ADP-50/PCI OME-DB-24P/24PD Isolated Input Board OME-DB-24R/24RD Relay Board OME-DB-24PR/24POR/24C Daughter Boards Comparison Table Pin Assignment All signals are TTL compatibleVCC GND Resource-allocated information How to Find the I/O AddressOME-PIO/PISO identification information PC’s physical slot informationPIODriverInit PIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAuxWSubVendor=0x80 wSubDevice=1 wSubAux=0x10 /* for PIOD96 Current sinking PIOGetConfigAddressSpace Enable all D/I/O operation of card0Enable all D/I/O operation of card1 ShowPIOPISOwSubVendor,wSubDevice,wSubAux ShowPIOPISOSlot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07 Assignment of I/O AddressAddress Read Write I/O Address MapRESET\ Control Register AUX Control RegisterAUX data Register Aux Status Register INT Mask Control RegisterINV3 INV2 INV1 INV0 Interrupt Polarity Control Register7 I/O Selection Control Register Read/Write 8-bit data Register Demo program How to install software & utility?Piopiso PIOPISO.EXE for Windows DEMO1 DEMO2 DEMO3 COUNTL++ DEMO4 COUNTL++ DEMO5 CNTL1=CNTL2=CNTL3=CNTL4=0 Page WARRANTY/DISCLAIMER Temperature