Omega Engineering OME-PIO-D96 manual OME-DB-24PR/24POR/24C

Page 22

2.6.7OME-DB-24PR/24POR/24C

OME-DB-24PR 24*power relay, 5A/250V

OME-DB-24POR 24*Photo MOS relay, 0.1A/350VAC

OME-DB-24C 24*open collector, 100mA per channel, 30V max.

The OME-DB-24PR, 24 channel power relay output board, consists of 8 form C and 16 form A electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 5A load at 250VAC/30VDC. The relay is energized by applying a 5 volt signal to the appropriate relay channel on the 20-pin flat cable connector (only 16 relays) or 50-pin flat cable connector(compatible for OME-DIO-24 series). Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated. To avoid overloading your PC’s power supply, this board needs a +12VDC or +24VDC external power supply.

Normal Open

Form A Relay

Com.

50Pin cable

					OME-DB-24PR
To 50pin connector					OME-DB-24PR

CN2 ~ CN4=D/O

OME-PIO-D96

Note:

50-Pin connector for OME-DIO-24, OME-DIO-48, OME-DIO-144, OME-PCI-D144, OME-PIO-D144, OME-PIO-D96, OME-PIO-D56, OME-PIO-D48, OME-PIO-D24

20-Pin connector for 16 channel digital output, OME-A-82X, OME-A-62X, OME-DIO- 64, OME-ISO-DA16/DA8

Channel : 16 Form A Relay , 8 Form C Relay

OME-PIO-D96 User Manual (Ver.1.1, Mar/2003)

---- 20

Image 22

Contents User’sGuide Benelux CanadaMexico Czech RepublicOME-PIO-D96 Table of Contents Features IntroductionOrder Description SpecificationsOptions Product Check List PCI Data Acquisition FamilyOME-PISO-series cost-effective generation, isolated cards Hardware configuration Board LayoutI/O port Location Enable I/O OperationRefer to DEMO1.C for demo program D/I/O Architecture Interrupt Operation Make sure the initial level is High or LowInterrupt Block Diagram of OME-PIO-D96 INTCHAN3INTCHAN0/1/2/3 Initialhigh, activelow Interrupt source COUNTL++Initiallow, activehigh Interrupt source Muliti Interrupt Source Read all interrupt state OME-DN-37 & OME-DN-50 Daughter BoardsOME-DB-37 OME-DB-8125OME-ADP-37/PCI & OME-ADP-50/PCI OME-DB-24P/24PD Isolated Input Board OME-DB-24R/24RD Relay Board OME-DB-24PR/24POR/24C Daughter Boards Comparison Table All signals are TTL compatible Pin AssignmentVCC GND OME-PIO/PISO identification information How to Find the I/O AddressResource-allocated information PC’s physical slot informationPIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAux PIODriverInitWSubVendor=0x80 wSubDevice=1 wSubAux=0x10 /* for PIOD96 Current sinking Enable all D/I/O operation of card0 PIOGetConfigAddressSpaceEnable all D/I/O operation of card1 ShowPIOPISO ShowPIOPISOwSubVendor,wSubDevice,wSubAuxAssignment of I/O Address Slot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07I/O Address Map Address Read WriteAUX Control Register RESET\ Control RegisterAUX data Register INT Mask Control Register Aux Status RegisterInterrupt Polarity Control Register INV3 INV2 INV1 INV07 I/O Selection Control Register Read/Write 8-bit data Register How to install software & utility? Demo programPiopiso PIOPISO.EXE for Windows DEMO1 DEMO2 DEMO3 COUNTL++ DEMO4 COUNTL++ DEMO5 CNTL1=CNTL2=CNTL3=CNTL4=0 Page WARRANTY/DISCLAIMER Temperature