Omega Engineering OME-PIO-D96 manual Specifications, Order Description, Options

Page 6

1.2Specifications

•All inputs are TTL compatible Logic high voltage: 2.4V (Min.) Logic low voltage: 0.8V (Max.)

•All outputs are TTL compatible Sink current: 64mA (Max.) Source current: 32mA (Max.)

•Environmental :

Operating Temperature: 0°C to 60°C

Storage Temperature: -20°C to 80°C

Humidity: 0 to 90% non-condensing

•Dimension: 180mm X 105mm

•Power Consumption: +5V @ 600mA

1.3Order Description

•OME-PIO-D96 : PCI bus 96-bit opto-22 board

1.3.1Options

•OME-DB-24P, OME-DB-24PD : 24 channel isolated D/I board

•OME-DB-24R, OME-DB-24RD : 24 channels relay board

•OME-DB-24PR, OME-DB-24PRD : 24 channels power relay board

•OME-DB-16P8R : 16 channels isolated D/I and 8 channels relay output board

•OME-DB-24POR : 24 channels Photo MOS output board

•OME-DB-24C : 24 channels open-collector output board

•OME-ADP-37/PCI : extender, 50 pin OPTO-22 header to DB-37 for PCI bus I/O boards

•OME-ADP-50/PCI : extender, 50 pin OPTO-22 header to 50-pin header, for PCI bus I/O boards

OME-PIO-D96 User Manual (Ver.1.1, Mar/2003)

---- 4

Image 6

Contents User’sGuide Benelux CanadaMexico Czech RepublicOME-PIO-D96 Table of Contents Features IntroductionSpecifications Order DescriptionOptions PCI Data Acquisition Family Product Check ListOME-PISO-series cost-effective generation, isolated cards Hardware configuration Board LayoutEnable I/O Operation I/O port LocationRefer to DEMO1.C for demo program D/I/O Architecture Interrupt Operation Make sure the initial level is High or LowInterrupt Block Diagram of OME-PIO-D96 INTCHAN3INTCHAN0/1/2/3 Initialhigh, activelow Interrupt source COUNTL++Initiallow, activehigh Interrupt source Muliti Interrupt Source Read all interrupt state OME-DN-37 & OME-DN-50 Daughter BoardsOME-DB-37 OME-DB-8125OME-ADP-37/PCI & OME-ADP-50/PCI OME-DB-24P/24PD Isolated Input Board OME-DB-24R/24RD Relay Board OME-DB-24PR/24POR/24C Daughter Boards Comparison Table All signals are TTL compatible Pin AssignmentVCC GND OME-PIO/PISO identification information How to Find the I/O AddressResource-allocated information PC’s physical slot informationPIODriverInit PIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAuxWSubVendor=0x80 wSubDevice=1 wSubAux=0x10 /* for PIOD96 Current sinking PIOGetConfigAddressSpace Enable all D/I/O operation of card0Enable all D/I/O operation of card1 ShowPIOPISO ShowPIOPISOwSubVendor,wSubDevice,wSubAuxAssignment of I/O Address Slot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07I/O Address Map Address Read WriteRESET\ Control Register AUX Control RegisterAUX data Register INT Mask Control Register Aux Status RegisterInterrupt Polarity Control Register INV3 INV2 INV1 INV07 I/O Selection Control Register Read/Write 8-bit data Register How to install software & utility? Demo programPiopiso PIOPISO.EXE for Windows DEMO1 DEMO2 DEMO3 COUNTL++ DEMO4 COUNTL++ DEMO5 CNTL1=CNTL2=CNTL3=CNTL4=0 Page WARRANTY/DISCLAIMER Temperature