Omega OMB-DAQBOARD-500 manual Secure the board by inserting the rear-panel adapter-plate screw

Page 10
9.Secure the board by inserting the rear-panel adapter-plate screw.

7.Refer to the figure at the right. Align the groove in the DaqBoard’s PCI edge-connector with the ridge of the desired PCI slot, and with the PC’s corresponding rear- panel slot.

8.Push the board firmly into the PCI slot. The board will snap into position.

9.Secure the board by inserting the rear-panel adapter-plate screw.

10.Using the previous steps, install additional boards into

 

available PCI bus-slots, if applicable to your application.

Installing a DaqBoard/500 Series Board

11.

Replace the computer’s cover.

 

12.

Plug in all cords and cables that were removed in step 1.

 

13.

Apply power to, and start up the PC.

 

Note: At this point some PCs may prompt you to insert an installation disk. While this is rare, if you do receive such a prompt simply place the install CD-ROM into the disk drive and follow additional screen prompts.

IG-4 DaqBoard/500 Series Installation Guide

947994

1138-0940, rev 1.1

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OMB-DAQBOARD-500 Series 16-Bit, 200-KHz PCI Data Acquisition BoardsUser’s Guide Shop online atServicing North America OMEGAnet Online Service omega.comInternet e-mail info@omega.com For immediate technical or application assistanceSpecifications and Calibration Warnings, Cautions, Notes, and Tips⇒ Programs ⇒ Omega DaqX Software 3 - Configuration Table of ContentsOMB-DAQBOARD-500 Series, Installation Guide 1 - Introduction 6 - Specifications GlossaryWindows Windows XP This product requires one of the following Operating SystemsDaqView/500 Authorization Code OMB-DAQBOARD-500 SeriesInstallation Guide Reference NoteInstallation, A Pictorial Overview Step 1 - Install SoftwareIMPORTANT Software must be installed before installing hardware Reference NotesIMPORTANT Bus Mastering DMA must be Enabled Step 2 - Install Boards in available PCI Bus-slots2. Remove the PC’s cover. Refer to your PC Owner’s Manual as needed 9. Secure the board by inserting the rear-panel adapter-plate screw Step 3 - Configure Boards Accessing the DaqBoard/500 Properties TabStep 4 - Test Hardware Using “Add Device”Test Hardware Tab Introduction Basic InformationDaqBoard/500 Series Block Diagram Block DiagramDaqBoard/500 Series User’s Manual Analog I/O Board FeaturesTimer 0 and Timer Digital I/ODaqBoard/500 Series User’s Manual Connections and Pinouts OverviewSignal 68-Pin SCSI Type III PinoutStandard 68-Pin SCSCI Type III, Socket Female Connector with Orb PowerDifferential Channels, Pin Reference Signal DefinitionsAnalog Input Channels HI + Pin #Clocks, Triggers, Counters, and Timers Power Line Ground LinesScrew Terminals for TB1 Side TB-100 Terminal Connector OptionScrew Terminals for TB2 Side 2-6 Connections & PinoutsDifferential Channels Screw Terminal Reference Connecting User WiringExternal Connections HI +Single-Ended Configuration Signal TypesChoosing A/D Input Configuration Single-EndedDifferential for Grounded Signal Sources Differential DIFFDifferential Configuration for Grounded Sources If the Input Signal is AC Coupled Differential for Floating Signal SourcesIf the Input Signal is DC Coupled Differential Configuration for Floating SourcesAnalog Input Configuration ConfigurationConfiguration through Software ADC RangesRange Configuration DAC RangesDAC OUTPUT DaqBoard/500 DAC Range Resolution Microvolt ResolutionOverview …… Out-of-the-BoxTM Software …… Software and Board OperationOut-of-theBoxTM Software Drivers for Third-party, Icon-driven Software …… DaqCOM Driver ……LabVIEW Drivers for Third-party, Icon-driven SoftwareDaqCOM Driver 4-2 Software and Board OperationTheory of Operation Process DefinitionsADC External Event Clocking Clocking the ADCADC Pacer Clocking ADC Maximum Clock RateADC External Gate Starting Triggering an ADC AcquisitionADC Software ADC External TriggerADC Clock and FIFO Errors Stopping an ADC Acquisition CLOCKClocking the DAC Digital AcquisitionDAC Software Update DaqBoard/500 Only4-8 Software and Board Operation Overview ……5-1 CE Standards and Directives …… Safety Conditions ……5-2 CE-ComplianceCE Standards and Directives Emissions/Immunity Conditions ……5-2Safety Conditions Emissions/Immunity ConditionsAnalog Inputs SpecificationsGeneral of calibrationAnalog Input Triggering/Clocking 6-2 SpecificationsDigital Inputs / Outputs Analog Outputs DaqBoard/500 OnlyPhysical & Environmental Counter - 1 Counter designated as CNTR1Glossary single-ended modereferenced to common Page Page WARRANTY/DISCLAIMER RETURN REQUESTS/INQUIRIESOMEGA…Of Course 324545A-01Shop online at omega.com TEMPERATURE
Top Page Image Contents