Omega Vehicle Security zSeries manual DIP Switch Setup Ethernet Coordinator

Page 18

2.7.3 DIP Switch Setup: Ethernet - Coordinator

4	1	1)	N/C
		2)	To change to default factory settings
		3)	To enable/disable DHCP
	OFF	4)	N/C

OFF ON1		ON
8	1 2 3	(Shown in
	SERIAL DEFAULT DHCP 4TERMINAL	"OFF" Position)
Coordinator
	Figure 2.9 Ethernet - 4 Position DIP Switch Setup

To set the Coordinator to factory default settings:

1)Slide DIP switch #2 to ON position.

2)Power the Coordinator on and wait about 10 seconds until the Coordinator fully boots up.

3)Set the DIP switch #2 back to OFF position (it does not matter if the Coordinator is powered ON or OFF, just make sure that the DIP switch is set to OFF, otherwise, every time the unit is power-cycled the factory settings will take over.

12

Image 18

Contents User’sGuide Page Table of Contents Appendix C Appendix aAppendix B Appendix DList of Figures Page Features Part Introduction EMC ConsiderationsDescription Description ZSeries Wireless System on the Ethernet Network Rear Part HardwareFrom TOP to Bottom Disassembly End Device Disassembly of the End DeviceParts of the Coordinator Dimensions and Mounting Coordinator Mounting the CoordinatorDIP Switches DIP Switch Setup Device ID did Device ID did 8 Position DIP Switch SetupDIP Switch Setup Network ID NID NIDDefinitions DIP Switch Setup Ethernet Coordinator Ethernet 4 Position DIP Switch Setup10 RJ45 Pinout 2 10Base-T Crossover Wiring Part Network Configuration Network ProtocolsDhcp Default IP Address DNSIP Address Network Connections SectionUsing the Telnet or Web browser Part OperationsIConnect Software Accessing the zSeries System for Configuration Setting a New IP Address over the Network Access ControlWireless Sensors Home Coordinator’s Configurations and OperationsPower Up Device Get Readings from the End Device Select Readings by GroupTheReadings fields are defined as follows Java Runtime Environment Setup Java Runtime Environment 1.4 Setup instructions10 Java 1.5.x.x. Screen Shots Accessing Coordinators units using the internet DiagnosticsAccessing Coordinators units over Peer-to-Peer network Grant codeBase http//192.168.1.200 Java PolicyJava Policy file and copy it onto a folder Permission java.security.AllPermissionDjava.security.policy=C\0JAVAPOLICY\javapolicy.txt 12 Java PolicyChart 13 Select Chart by GroupChart Diagnostic 15 DiagnosticConfiguration 16 ConfigurationSensor Setup 17 Sensor Setup by Group18 Sensor Setup Update Checked BoxSensor Parameters Web Server Host NameTelnet Setup HTTPget ProgramWhere HTTPget using PortHttpget -r -S Erdgall 192.168.1.1352000 -C1 -q 2000Httpget -r -S 00000000 192.168.1.2001 where HTTPget and ARP to Setup Device IP AddressArp -s 192.168.1.200 00-03-34-00-00-06-b6 ARP Protocol22 ARP Commands and Responses ILog Software 23 iLog Software Logging Data for End Deice #1, 3Installation Mail Notifier SoftwareEmail Address Setup Email SetupDevice Setting and Configuration EQNF003Alarm Editor Mail Notifier Device SettingPart Environment / Operating ConditionsGeneral Deployment Guidelines Control Room Office Operation in BuildingsWith Line-of-Sight Distance feet Radius feetMaterial Type Possible Signal Reduction Without Line-of-SightCasing and Closure Around the Antenna Fine Adjustment in Performance ChannelsPart 6 Specifications Relative HumidityApprovals DIP Switches DhcpAppendix Aglossary Appendix BIP Address Or Dotted Notation Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Mask Dotted Notation Mask Binary Mask BitsDec Binary Ascii Chart Dec Hex BinaryAscii Char No Parity No parityAppendix D Ascii Chart Continuation Dec Hex Ctrl Key Ascii Control Codes DefinitionChar Equiv Appendix E ILog Error Messages Error # Description Telnet Commands Table ErdgAppendix F Telnet Commands Table Response 7 EngrLAB 01000010Appendix G Frequently Asked Questions FAQ OpenLost Page WARRANTY/DISCLAIMER Shop on line at omega.com