Omega Vehicle Security zSeries manual Disassembly End Device, Disassembly of the End Device

Page 13

2.4 Disassembly - End Device
You may need to open the unit for one of the following reasons:
•	To turn on Power Switch.	Figure 2.2 for mounting dimensions.
•	To mount unit to wall. Refer to
•	To connect or replace the batteries, (note the polarity of batteries).
•	To access JTAG connector.

Remove Cover as shown below, by pressing sides of cover to release latches.

LATCH

TRAY BATTERY CLIPS

8

1

JTAG

COVER

LATCH

DIP SWITCH SENSOR

BOARD

EXTERNAL SENSOR/ PROBE

MOUNTING SCREW POWER SWITCH

Figure 2.4 Disassembly of the End Device

7

Image 13

Contents User’sGuide Page Table of Contents Appendix B Appendix aAppendix C Appendix DList of Figures Page Features EMC Considerations Part IntroductionDescription Description ZSeries Wireless System on the Ethernet Network Part Hardware RearFrom TOP to Bottom Disassembly of the End Device Disassembly End DeviceParts of the Coordinator Mounting the Coordinator Dimensions and Mounting CoordinatorDevice ID did 8 Position DIP Switch Setup DIP Switches DIP Switch Setup Device ID didNID DIP Switch Setup Network ID NIDDefinitions Ethernet 4 Position DIP Switch Setup DIP Switch Setup Ethernet Coordinator10 RJ45 Pinout 2 10Base-T Crossover Wiring Network Protocols Part Network ConfigurationDhcp DNS Default IP AddressIP Address Section Network ConnectionsPart Operations Using the Telnet or Web browserIConnect Software Accessing the zSeries System for Configuration Access Control Setting a New IP Address over the NetworkCoordinator’s Configurations and Operations Wireless Sensors HomePower Up Device Select Readings by Group Get Readings from the End DeviceTheReadings fields are defined as follows Java Runtime Environment 1.4 Setup instructions Java Runtime Environment Setup10 Java 1.5.x.x. Screen Shots Diagnostics Accessing Coordinators units using the internetAccessing Coordinators units over Peer-to-Peer network Java Policy file and copy it onto a folder Java PolicyGrant codeBase http//192.168.1.200 Permission java.security.AllPermission12 Java Policy Djava.security.policy=C\0JAVAPOLICY\javapolicy.txt13 Select Chart by Group ChartChart 15 Diagnostic Diagnostic16 Configuration Configuration17 Sensor Setup by Group Sensor SetupUpdate Checked Box 18 Sensor SetupSensor Parameters Host Name Web ServerHTTPget Program Telnet SetupHttpget -r -S Erdgall 192.168.1.1352000 -C1 -q HTTPget using PortWhere 2000Arp -s 192.168.1.200 00-03-34-00-00-06-b6 HTTPget and ARP to Setup Device IP AddressHttpget -r -S 00000000 192.168.1.2001 where ARP Protocol22 ARP Commands and Responses 23 iLog Software Logging Data for End Deice #1, 3 ILog SoftwareMail Notifier Software InstallationEmail Setup Email Address SetupEQNF003 Device Setting and ConfigurationMail Notifier Device Setting Alarm EditorEnvironment / Operating Conditions PartGeneral Deployment Guidelines Operation in Buildings Control Room OfficeDistance feet Radius feet With Line-of-SightWithout Line-of-Sight Material Type Possible Signal ReductionCasing and Closure Around the Antenna Channels Fine Adjustment in PerformanceRelative Humidity Part 6 SpecificationsApprovals Dhcp DIP SwitchesAppendix Aglossary Appendix BIP Address Address Class Mask Binary Value Mask Decimal Value Appendix CIP NetmaskOr Dotted Notation Mask Dotted Notation Mask Binary Mask BitsAscii Ascii Chart Dec Hex BinaryDec Binary Char No Parity No parityDec Hex Ctrl Key Ascii Control Codes Definition Appendix D Ascii Chart ContinuationChar Equiv Appendix E ILog Error Messages Error # Description Erdg Telnet Commands TableResponse 7 EngrLAB 01000010 Appendix F Telnet Commands TableOpen Appendix G Frequently Asked Questions FAQLost Page WARRANTY/DISCLAIMER Shop on line at omega.com