Omega Vehicle Security zSeries manual Telnet Setup, HTTPget Program

Page 44

4.3.9 Access Control (continued)

IP Address: The IP (Internet Protocol) address is a 32-bit number that identifies each sender or receiver of information that is sent in packets across the Ethernet or the Internet. The Coordinator’s default IP address is 192.168.1.200. The Coordinator’s IP address should be changed to fit user’s networking environment. Consult with your IT department for obtaining an IP address.

The DHCP will be enabled in the Coordinator if its IP address is set to 0.0.0.0. The DHCP can also be enabled by setting the DIP switch #3 to ON position. G way Address: A gateway is a network point that acts as an entrance to another network. A gateway is often associated with a router, which knows where to direct a given packet of data that arrives at the gateway. If the Coordinator is sending packets to another network node that is not on the same network on which the Coordinator is connected, a gateway address needs to be given to the Coordinator. The gateway address should be the IP address of the router connected to the same LAN to which the Coordinator is connected. The Coordinator default gateway address is 0.0.0.0. Consult with your IT department for obtaining a gateway address.

Subnet Mask: It’s a 32-bit number that is used to determine which part of the IP address is the network portion and which part is the host portion. The Coordinator default subnet mask is 255.255.255.0. Consult with your IT department for obtaining a subnet mask.

Power Recycle: Reboots the embedded server. Note that all updated network parameters take effect after reboot.

Changes made in the Access Control page can be saved permanently by pressing the Save button and power recycling the Coordinator (press Power Recycle button). Pressing the Reset button will set all the fields back to their default values.

4.4 Telnet Setup

In the Configuration page, set the TCP Connections to 1 - 5 other than 0, and use a telnet simulation program to connect to the Coordinator (using Port 2000). The command can be sent to query the Coordinator and get a response back.

4.5 HTTPget Program

The HTTPget software is used to send a single HTTP or TCP request to an Coordinator. In contrast, the telnet or Hyperterminal programs allow a continuous connection with multiple requests to be sent to the Coordinator.

Generally HTTPget is used for simply programming an IP address to the Coordinator or for quickly obtaining a reading from a device.

The Coordinator must be configured from the configuration web page so that the "TCP Connections" indicates any number between 1 and 5. Make sure that the Port Field number indicates 2000.

38

Page 43 Page 45
Image 44
Page 43 Page 45
Contents User’sGuide Page Table of Contents Appendix a Appendix BAppendix C Appendix DList of Figures Page Features Description Part IntroductionEMC Considerations Description ZSeries Wireless System on the Ethernet Network Rear Part HardwareFrom TOP to Bottom Disassembly End Device Disassembly of the End DeviceParts of the Coordinator Dimensions and Mounting Coordinator Mounting the CoordinatorDIP Switches DIP Switch Setup Device ID did Device ID did 8 Position DIP Switch SetupDefinitions DIP Switch Setup Network ID NIDNID DIP Switch Setup Ethernet Coordinator Ethernet 4 Position DIP Switch Setup10 RJ45 Pinout 2 10Base-T Crossover Wiring Dhcp Part Network ConfigurationNetwork Protocols IP Address Default IP AddressDNS Network Connections SectionUsing the Telnet or Web browser Part OperationsIConnect Software Accessing the zSeries System for Configuration Setting a New IP Address over the Network Access ControlWireless Sensors Home Coordinator’s Configurations and OperationsPower Up Device Get Readings from the End Device Select Readings by GroupTheReadings fields are defined as follows Java Runtime Environment Setup Java Runtime Environment 1.4 Setup instructions10 Java 1.5.x.x. Screen Shots Accessing Coordinators units over Peer-to-Peer network Accessing Coordinators units using the internetDiagnostics Java Policy Java Policy file and copy it onto a folderGrant codeBase http//192.168.1.200 Permission java.security.AllPermissionDjava.security.policy=C\0JAVAPOLICY\javapolicy.txt 12 Java PolicyChart 13 Select Chart by GroupChart Diagnostic 15 DiagnosticConfiguration 16 ConfigurationSensor Setup 17 Sensor Setup by Group18 Sensor Setup Update Checked BoxSensor Parameters Web Server Host NameTelnet Setup HTTPget ProgramHTTPget using Port Httpget -r -S Erdgall 192.168.1.1352000 -C1 -qWhere 2000HTTPget and ARP to Setup Device IP Address Arp -s 192.168.1.200 00-03-34-00-00-06-b6Httpget -r -S 00000000 192.168.1.2001 where ARP Protocol22 ARP Commands and Responses ILog Software 23 iLog Software Logging Data for End Deice #1, 3Installation Mail Notifier SoftwareEmail Address Setup Email SetupDevice Setting and Configuration EQNF003Alarm Editor Mail Notifier Device SettingGeneral Deployment Guidelines PartEnvironment / Operating Conditions Control Room Office Operation in BuildingsWith Line-of-Sight Distance feet Radius feetCasing and Closure Around the Antenna Material Type Possible Signal ReductionWithout Line-of-Sight Fine Adjustment in Performance ChannelsPart 6 Specifications Relative HumidityApprovals DIP Switches DhcpAppendix Aglossary Appendix BIP Address Appendix CIP Netmask Address Class Mask Binary Value Mask Decimal ValueOr Dotted Notation Mask Dotted Notation Mask Binary Mask BitsAscii Chart Dec Hex Binary AsciiDec Binary Char No Parity No parityChar Equiv Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Ascii Control Codes Definition Appendix E ILog Error Messages Error # Description Telnet Commands Table ErdgAppendix F Telnet Commands Table Response 7 EngrLAB 01000010Lost Appendix G Frequently Asked Questions FAQOpen Page WARRANTY/DISCLAIMER Shop on line at omega.com
Top Page Image Contents