Omega Vehicle Security zSeries manual Part Introduction, EMC Considerations, Description

Page 8

PART 1

INTRODUCTION

1.1 Safety and EMC Considerations

Refer to the Environment/Operating Conditions Section

EMC Considerations

• Whenever EMC is an issue, always use shielded cables.

• Never run signal and power wires in the same conduit.

• Use twisted-pair wires for signal connections.

• Install Ferrite Bead(s) on signal wires close to the instrument if EMC problems persist.

Failure to follow all instructions and warnings may result in injury!

1.2 Before You Begin

Inspecting Your Shipment: Remove the packing slip and verify that you have received everything listed. Inspect the container and equipment for signs of damage as soon as you receive the shipment. Note any evidence of rough handling in transit. Immediately report any damage to the shipping agent. The carrier will not honor damage claims unless all shipping material is saved for inspection. After examining and removing the contents, save the packing material and carton in the event reshipment is necessary. Customer Service: If you need assistance, please contact the Customer Service Department nearest you.

Manuals, Software: The latest Operation Manual as well as free configuration software (iConnect), data-logging software (iLog) and Mail Notifier are available at the website listed on the cover page of this manual or on the CD-ROM enclosed with your shipment.

1.3 Description

The zSeries wireless sensor system provides Web-based monitoring of Temperature, Humidity, and Barometric Pressure in critical HVAC and Refrigeration applications. The compact wireless “End Devices” mount discretely on the wall in clean rooms, laboratories, museums, computer server rooms, warehouses, and any remote facility. The wireless End Devices are powered by two AA 1.5 volt alkaline batteries.

The End Devices transmit up to 300 feet (without obstructions or interference) to a “Coordinator” connected directly to an Ethernet network and the Internet. The wireless system complies with IEEE 802.15.4 operating at 2.4GHz.

The zSeries system allows you to monitor and record Temperature, Relative Humidity, and Barometric Pressure over an Ethernet network or the Internet without any special software-just your Web Browser.

We offer a selection of End Devices for a variety of applications. Each E nd Device supports one or two sensors. En d Devices are available with built-in sensors, with external sensor probes, and with both built-in and external sensors. The external sensors are designed for harsh environments such as outdoor weather, in HVAC ducts, in freezers and refrigerators.

2

Page 7 Page 9
Image 8
Page 7 Page 9
Contents User’sGuide Page Table of Contents Appendix a Appendix BAppendix C Appendix DList of Figures Page Features Description Part IntroductionEMC Considerations Description ZSeries Wireless System on the Ethernet Network Rear Part HardwareFrom TOP to Bottom Disassembly End Device Disassembly of the End DeviceParts of the Coordinator Dimensions and Mounting Coordinator Mounting the CoordinatorDIP Switches DIP Switch Setup Device ID did Device ID did 8 Position DIP Switch SetupDefinitions DIP Switch Setup Network ID NIDNID DIP Switch Setup Ethernet Coordinator Ethernet 4 Position DIP Switch Setup10 RJ45 Pinout 2 10Base-T Crossover Wiring Dhcp Part Network ConfigurationNetwork Protocols IP Address Default IP AddressDNS Network Connections SectionUsing the Telnet or Web browser Part OperationsIConnect Software Accessing the zSeries System for Configuration Setting a New IP Address over the Network Access ControlWireless Sensors Home Coordinator’s Configurations and OperationsPower Up Device Get Readings from the End Device Select Readings by GroupTheReadings fields are defined as follows Java Runtime Environment Setup Java Runtime Environment 1.4 Setup instructions10 Java 1.5.x.x. Screen Shots Accessing Coordinators units over Peer-to-Peer network Accessing Coordinators units using the internetDiagnostics Java Policy Java Policy file and copy it onto a folderGrant codeBase http//192.168.1.200 Permission java.security.AllPermissionDjava.security.policy=C\0JAVAPOLICY\javapolicy.txt 12 Java PolicyChart 13 Select Chart by GroupChart Diagnostic 15 DiagnosticConfiguration 16 ConfigurationSensor Setup 17 Sensor Setup by Group18 Sensor Setup Update Checked BoxSensor Parameters Web Server Host NameTelnet Setup HTTPget ProgramHTTPget using Port Httpget -r -S Erdgall 192.168.1.1352000 -C1 -qWhere 2000HTTPget and ARP to Setup Device IP Address Arp -s 192.168.1.200 00-03-34-00-00-06-b6Httpget -r -S 00000000 192.168.1.2001 where ARP Protocol22 ARP Commands and Responses ILog Software 23 iLog Software Logging Data for End Deice #1, 3Installation Mail Notifier SoftwareEmail Address Setup Email SetupDevice Setting and Configuration EQNF003Alarm Editor Mail Notifier Device SettingGeneral Deployment Guidelines PartEnvironment / Operating Conditions Control Room Office Operation in BuildingsWith Line-of-Sight Distance feet Radius feetCasing and Closure Around the Antenna Material Type Possible Signal ReductionWithout Line-of-Sight Fine Adjustment in Performance ChannelsPart 6 Specifications Relative HumidityApprovals DIP Switches DhcpAppendix Aglossary Appendix BIP Address Appendix CIP Netmask Address Class Mask Binary Value Mask Decimal ValueOr Dotted Notation Mask Dotted Notation Mask Binary Mask BitsAscii Chart Dec Hex Binary AsciiDec Binary Char No Parity No parityChar Equiv Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Ascii Control Codes Definition Appendix E ILog Error Messages Error # Description Telnet Commands Table ErdgAppendix F Telnet Commands Table Response 7 EngrLAB 01000010Lost Appendix G Frequently Asked Questions FAQOpen Page WARRANTY/DISCLAIMER Shop on line at omega.com
Top Page Image Contents