Omega Vehicle Security zSeries manual Part Operations, Using the Telnet or Web browser

Page 23

PART 4

OPERATIONS

This Coordinator can be used and configured in several ways, depending on user’s preference and network setup. It can be configured using a Web browser, like Netscape or Internet Explorer. It can also be configured using the iConnect Configuration Software. If DHCP and DNS servers are configured to exchange information, the connection will be very simple. All you need to do is to enable DHCP on the Coordinator (see Section 3.3) and use a straight through network cable to connect the Coordinator to an Ethernet hub or switch and power it up. Now, you can use the Coordinator’s default Host (Domain) Name, which is zxxxx (where xxxx are the last four characters of its MAC address) to access the Coordinator’s Web Server.

If DHCP is not the preferred method, you can configure your PC’s network connection with an IP address of 192.168.1.x that is in the same range as the Coordinator’s default IP address (192.168.1.200) and connect to the Coordinator using a cross-over network cable between your PC’s network port and the Coordinator. After you’redone with configuring the Coordinator, you can always set your PC back to its original settings. (See Section 3.5.2 for more details).

On your computer, from the MS-DOS Prompt window type "ping 192.168.1.200” and press Enter. If DHCP and DNS servers are used type “ping zxxxx”, where xxxx are the last four digits of the Coordinator’s MAC address, located on the back of the device. You should get a reply as shown in Figure 4.1.

4.0 Testing the Connection

C:\>ping z03ec

Pinging z03ec with 32 bytes of data:

Reply from z03ec: bytes=32 time=15ms TTL=60

Reply from z03ec: bytes=32 time=8ms TTL=60

Reply from z03ec: bytes=32 time=8ms TTL=60

Reply from z03ec: bytes=32 time=8ms TTL=60

Pinging statistics for z03ec:

Packets: Sent=4, Received=4, Lost=0 (0% loss)

Approximate round trip times in milli-seconds: Minimum=8ms, Maximum=15ms, Average=9ms

Figure 4.1 Pinging the Coordinator from MS-DOS Prompt
This proves that the connection is proper and you can get into configuration or run mode
using the Telnet or Web browser.	17

Image 23

Contents User’sGuide Page Table of Contents Appendix D Appendix aAppendix B Appendix CList of Figures Page Features Description Part IntroductionEMC Considerations Description ZSeries Wireless System on the Ethernet Network Part Hardware RearFrom TOP to Bottom Disassembly of the End Device Disassembly End DeviceParts of the Coordinator Mounting the Coordinator Dimensions and Mounting CoordinatorDevice ID did 8 Position DIP Switch Setup DIP Switches DIP Switch Setup Device ID didDefinitions DIP Switch Setup Network ID NIDNID Ethernet 4 Position DIP Switch Setup DIP Switch Setup Ethernet Coordinator10 RJ45 Pinout 2 10Base-T Crossover Wiring Dhcp Part Network ConfigurationNetwork Protocols IP Address Default IP AddressDNS Section Network ConnectionsPart Operations Using the Telnet or Web browserIConnect Software Accessing the zSeries System for Configuration Access Control Setting a New IP Address over the NetworkCoordinator’s Configurations and Operations Wireless Sensors HomePower Up Device Select Readings by Group Get Readings from the End DeviceTheReadings fields are defined as follows Java Runtime Environment 1.4 Setup instructions Java Runtime Environment Setup10 Java 1.5.x.x. Screen Shots Accessing Coordinators units over Peer-to-Peer network Accessing Coordinators units using the internetDiagnostics Permission java.security.AllPermission Java PolicyJava Policy file and copy it onto a folder Grant codeBase http//192.168.1.20012 Java Policy Djava.security.policy=C\0JAVAPOLICY\javapolicy.txt13 Select Chart by Group ChartChart 15 Diagnostic Diagnostic16 Configuration Configuration17 Sensor Setup by Group Sensor SetupUpdate Checked Box 18 Sensor SetupSensor Parameters Host Name Web ServerHTTPget Program Telnet Setup2000 HTTPget using PortHttpget -r -S Erdgall 192.168.1.1352000 -C1 -q WhereARP Protocol HTTPget and ARP to Setup Device IP AddressArp -s 192.168.1.200 00-03-34-00-00-06-b6 Httpget -r -S 00000000 192.168.1.2001 where22 ARP Commands and Responses 23 iLog Software Logging Data for End Deice #1, 3 ILog SoftwareMail Notifier Software InstallationEmail Setup Email Address SetupEQNF003 Device Setting and ConfigurationMail Notifier Device Setting Alarm EditorGeneral Deployment Guidelines PartEnvironment / Operating Conditions Operation in Buildings Control Room OfficeDistance feet Radius feet With Line-of-SightCasing and Closure Around the Antenna Material Type Possible Signal ReductionWithout Line-of-Sight Channels Fine Adjustment in PerformanceRelative Humidity Part 6 SpecificationsApprovals Dhcp DIP SwitchesAppendix Aglossary Appendix BIP Address Mask Dotted Notation Mask Binary Mask Bits Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Or Dotted NotationChar No Parity No parity Ascii Chart Dec Hex BinaryAscii Dec BinaryChar Equiv Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Ascii Control Codes Definition Appendix E ILog Error Messages Error # Description Erdg Telnet Commands TableResponse 7 EngrLAB 01000010 Appendix F Telnet Commands TableLost Appendix G Frequently Asked Questions FAQOpen Page WARRANTY/DISCLAIMER Shop on line at omega.com