Omega Vehicle Security OME-PIO-D56 manual Muliti-Interrupt Source, PC0 PC1 PC2 PC3

Page 18

2.4.5Muliti-Interrupt Source

Assume: PC0 is initial Low, active High, PC1 is initial High, active Low PC2 is initial Low, active High PC3 is initial High, active Low

as follows :

PC0

PC1

PC2

PC3

PC0 & PC1 are active at the same time.

PC2 & PC3 are active at the same time.

PC0 & PC1 are return to normal at the same time.

PC2 & PC3 are return to normal at the same time.

Refer to DEMO5.C for source program. All these four falling-edge & rising-edge can be detected by DEMO5.C.

Note: When the interrupt is active, the user program has to identify the active signals. These signals may be active at the same time. The interrupt service routine has to service all active signals at the same time.

OME-PIO-D56/PIO-D24 User Manual (Ver.2.1, Oct/2003, PPH-005-21)

---- 16

Image 18

Contents User’sGuide Benelux CanadaMexico Czech RepublicOME-PIO-D56/D24 Table of Contents Features IntroductionSpecifications Order DescriptionOptions Product Checklist PCI Data Acquisition FamilyOME-PISO-series cost-effective generation, isolated cards Hardware configuration Board LayoutI/O Port Location Enabling I/O Operation1 DI/DO Port Architecture CON3 Select Sec RESET\ Sec DI Port Architecture CON2 Do Port Architecture CON1 If INT signal is Low now Æ select the non-inverted input Interrupt OperationMake sure the initial level is High or Low Interrupt Block Diagram of OME-PIO D56/D24 Interrupt output signal of OME-PIO-D56/OME-PIO-D24, INT\ isINTCHAN0/1/2/3 Initialhigh, activelow Interrupt source COUNTL++Initiallow, activehigh Interrupt source Muliti-Interrupt Source PC0 PC1 PC2 PC3Read all interrupt state OME-DN-37 Daughter BoardsOME-DB-37 OME-DB-8125OME-ADP-20/PCI OME-DB-24PD Isolated Input Board OME-DB-24RD Relay Board OME-DB-24PRD, OME-DB-24POR, OME DB-24C Daughter Board Comparison Table All signals are TTL compatible Pin AssignmentDI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 DI9 PIO/PISO identification information How to Find the I/O AddressResource-allocated information PC’s physical slot informationWSubVendor=0x80 wSubDevice=1 wSubAux=0x40 For PIODriverInitPIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAux D56/D24Printf\nThrer are %d Piopiso Cards in this PC,wBoards OME-PISO-P32C32 PIOGetConfigAddressSpace Enable all D/I/O operations of card0Enable all D/I/O operations of card1 ShowPIOPISO ShowPIOPISOwSubVendor,wSubDevice,wSubAuxAssignment of I/O Address Slot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07I/O Address Map Address Read WriteRESET\ Control Register AUX Control RegisterAUX data Register INT Mask Control Register Aux Status RegisterInterrupt Polarity Control Register 7 I/O Selection Control RegisterRead/Write 8-bit data Register How to install software & utility? Demo programPiopiso PIOPISO.EXE for Windows DEMO1 DEMO2 DEMO3 COUNT=0COUNT++ DEMO4 COUNT++ DEMO5 PC3CNTL1=CNTL2=CNTL3=CNTL4=0 Page WARRANTY/DISCLAIMER Temperature