Omega Vehicle Security OME-PIO-D56 manual Introduction, Features

Page 5

1.Introduction

The OME-PIO-D56/OME-OME-PIO-D24 provides 56/24 TTL digital I/O lines. The OME-PIO-D56/OME-OME-PIO-D24 consists of one 24-bit bi-directional port, one 16-bit input port and one 16-bit output port (only for OME-PIO-D56). The 24-bit port supports three 8-bit groups PA, PB & PC. Each 8-bit group can be individually configured to function as either an input or an output. All groups using 24-bit bi- directional ports are configured as inputs upon power-up or reset.

Use the OME-DB-24PD to connect the input port for either isolation purposes, or to interface to the output port for relay control. The OME-PIO-D56/OME-PIO-D24 has one D-sub connector and two 20-pinflat-cable connectors (only for OME-PIO- D56). The flat cable can be connected to an OME-ADP-20/PCI adapter. The adapter can be fixed on the chassis. It can be installed in a 5V PCI bus and supports “Plug & Play”.

1.1Features

PCI bus

Up to 56/24(OME-PIO-D56/OME-PIO-D24) channels of digital I/O

All I/O lines buffered on the board

Eight-bit groups independently selectable for I/O on 24-bit port

Input / Output programmable I/O ports under software control

Double side SMD, short card.

Connects directly to OME-DB-24PR, OME-DB-24PD, OME-DB-24RD, OME-DB-24PRD, OME-DB-16P8R, OME-DB-24POR, OME-DB-24SSR or OME-DB-24C

4 interrupt sources: PC0, PC1, PC2, PC3

One DB37 connector, two 20-pinflat-cable connectors (only for OME-PIO-D56)

High drive capability

Automatically detected by Windows 95/98/2000/XP

No base address or IRQ switches to set

OME-PIO-D56/OME-PIO-D24 User Manual (Ver.2.1, Oct/2003)

---- 3

Image 5
Contents User’sGuide Mexico CanadaBenelux Czech RepublicOME-PIO-D56/D24 Table of Contents Introduction FeaturesOptions SpecificationsOrder Description OME-PISO-series cost-effective generation, isolated cards Product ChecklistPCI Data Acquisition Family Board Layout Hardware configuration1 DI/DO Port Architecture CON3 I/O Port LocationEnabling I/O Operation Select Sec RESET\ Sec DI Port Architecture CON2 Do Port Architecture CON1 Make sure the initial level is High or Low If INT signal is Low now Æ select the non-inverted inputInterrupt Operation Interrupt output signal of OME-PIO-D56/OME-PIO-D24, INT\ is Interrupt Block Diagram of OME-PIO D56/D24INTCHAN0/1/2/3 COUNTL++ Initialhigh, activelow Interrupt sourceInitiallow, activehigh Interrupt source PC0 PC1 PC2 PC3 Muliti-Interrupt SourceRead all interrupt state OME-DB-37 Daughter BoardsOME-DN-37 OME-DB-8125OME-ADP-20/PCI OME-DB-24PD Isolated Input Board OME-DB-24RD Relay Board OME-DB-24PRD, OME-DB-24POR, OME DB-24C Daughter Board Comparison Table Pin Assignment All signals are TTL compatibleDI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 DI9 Resource-allocated information How to Find the I/O AddressPIO/PISO identification information PC’s physical slot informationPIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAux PIODriverInitWSubVendor=0x80 wSubDevice=1 wSubAux=0x40 For D56/D24Printf\nThrer are %d Piopiso Cards in this PC,wBoards OME-PISO-P32C32 Enable all D/I/O operations of card1 PIOGetConfigAddressSpaceEnable all D/I/O operations of card0 ShowPIOPISOwSubVendor,wSubDevice,wSubAux ShowPIOPISOSlot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07 Assignment of I/O AddressAddress Read Write I/O Address MapAUX data Register RESET\ Control RegisterAUX Control Register Aux Status Register INT Mask Control Register7 I/O Selection Control Register Interrupt Polarity Control RegisterRead/Write 8-bit data Register Demo program How to install software & utility?Piopiso PIOPISO.EXE for Windows DEMO1 DEMO2 COUNT=0 DEMO3COUNT++ DEMO4 COUNT++ PC3 DEMO5CNTL1=CNTL2=CNTL3=CNTL4=0 Page WARRANTY/DISCLAIMER Temperature