Omega Vehicle Security OME-PIO-D56 manual OME-DB-24RD Relay Board

Page 23

2.5.6OME-DB-24RD Relay Board

The OME-DB-24RD, a 24 channel relay output board, consists of 24 form C relays for efficient, programmable load switching. The relays are energized by applying a 12V/24V signal to the appropriate relay channel on the 50-pin flat connector. There are 24 enunciator LEDs for each relay which light when their associated relay is activated.

Form C Relay

OME-PIO- D56/PIO-D24

Normal Open

Normal Close

Com

OME-DB-24RD

Note:

Channel : 24 Form C Relay

Relay: Switch up to 0.5A at 110ACV

			or 1A at 24DCV

	OME-DB-24RD
50-pin flat-cable header	Yes
D-sub 37-pin header	Yes

OME-DB-24R, OME-DB-24RD		24*Relay (120V, 0.5A)
OME-DB-24PR,OME-DB-24PRD		24* Power Relay (250V, 5A)
OME-DB-24POR		24*photo MOS Relay (350V, 01.A)
OME-DB-24SSR		24*SSR (250VAC, 4A)
OME-DB-24C		24*O.C. (30V, 100 mA)
OME-DB-16P8R		16Relay (120V, 0.5A) + 8isolated input

OME-PIO-D56/OME-PIO-D24 User Manual (Ver.2.1, Oct/2003)

---- 21

Image 23

Contents User’sGuide Czech Republic CanadaMexico BeneluxOME-PIO-D56/D24 Table of Contents Introduction FeaturesOptions SpecificationsOrder Description OME-PISO-series cost-effective generation, isolated cards Product ChecklistPCI Data Acquisition Family Board Layout Hardware configuration1 DI/DO Port Architecture CON3 I/O Port LocationEnabling I/O Operation Select Sec RESET\ Sec DI Port Architecture CON2 Do Port Architecture CON1 Make sure the initial level is High or Low If INT signal is Low now Æ select the non-inverted inputInterrupt Operation Interrupt output signal of OME-PIO-D56/OME-PIO-D24, INT\ is Interrupt Block Diagram of OME-PIO D56/D24INTCHAN0/1/2/3 COUNTL++ Initialhigh, activelow Interrupt sourceInitiallow, activehigh Interrupt source PC0 PC1 PC2 PC3 Muliti-Interrupt SourceRead all interrupt state OME-DB-8125 Daughter BoardsOME-DB-37 OME-DN-37OME-ADP-20/PCI OME-DB-24PD Isolated Input Board OME-DB-24RD Relay Board OME-DB-24PRD, OME-DB-24POR, OME DB-24C Daughter Board Comparison Table Pin Assignment All signals are TTL compatibleDI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 DI9 PC’s physical slot information How to Find the I/O AddressResource-allocated information PIO/PISO identification informationD56/D24 PIODriverInitPIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAux WSubVendor=0x80 wSubDevice=1 wSubAux=0x40 ForPrintf\nThrer are %d Piopiso Cards in this PC,wBoards OME-PISO-P32C32 Enable all D/I/O operations of card1 PIOGetConfigAddressSpaceEnable all D/I/O operations of card0 ShowPIOPISOwSubVendor,wSubDevice,wSubAux ShowPIOPISOSlot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07 Assignment of I/O AddressAddress Read Write I/O Address MapAUX data Register RESET\ Control RegisterAUX Control Register Aux Status Register INT Mask Control Register7 I/O Selection Control Register Interrupt Polarity Control RegisterRead/Write 8-bit data Register Demo program How to install software & utility?Piopiso PIOPISO.EXE for Windows DEMO1 DEMO2 COUNT=0 DEMO3COUNT++ DEMO4 COUNT++ PC3 DEMO5CNTL1=CNTL2=CNTL3=CNTL4=0 Page WARRANTY/DISCLAIMER Temperature