Omega Vehicle Security OME-PIO-D56 manual Select Sec RESET\ Sec

Page 10

I/O select (Sec. 3.3.7)

RESET\ (Sec. 3.3.1)

disable\

Data

input Latch

(Sec. 3.3.8)

Clock input

D/O latch CKT

disable

Data

Buffer input

(Sec. 3.3.8)

Clock input

D/I buffer CKT

D/I/O

•When the RESET\ is in Low-state Æ all D/I/O operations are disabled

•When the RESET\ is in High-state Æ all D/I/O operation are enabled.

•If D/I/O is configured as D/I port Æ D/I= external input signal

•If D/I/O is configured as D/O port Æ D/I = read back of D/O

•If D/I/O is configured as D/I port Æ send to D/O will change the D/O latch register only. The D/I & external input signals will not change.

OME-PIO-D56/PIO-D24 User Manual (Ver.2.1, Oct/2003, PPH-005-21)

---- 8

Image 10

Contents User’sGuide Benelux CanadaMexico Czech RepublicOME-PIO-D56/D24 Table of Contents Features IntroductionOrder Description SpecificationsOptions PCI Data Acquisition Family Product Checklist OME-PISO-series cost-effective generation, isolated cards Hardware configuration Board LayoutEnabling I/O Operation I/O Port Location1 DI/DO Port Architecture CON3 Select Sec RESET\ Sec DI Port Architecture CON2 Do Port Architecture CON1 Interrupt Operation If INT signal is Low now Æ select the non-inverted inputMake sure the initial level is High or Low Interrupt Block Diagram of OME-PIO D56/D24 Interrupt output signal of OME-PIO-D56/OME-PIO-D24, INT\ isINTCHAN0/1/2/3 Initialhigh, activelow Interrupt source COUNTL++Initiallow, activehigh Interrupt source Muliti-Interrupt Source PC0 PC1 PC2 PC3Read all interrupt state OME-DN-37 Daughter BoardsOME-DB-37 OME-DB-8125OME-ADP-20/PCI OME-DB-24PD Isolated Input Board OME-DB-24RD Relay Board OME-DB-24PRD, OME-DB-24POR, OME DB-24C Daughter Board Comparison Table All signals are TTL compatible Pin AssignmentDI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 DI9 PIO/PISO identification information How to Find the I/O AddressResource-allocated information PC’s physical slot informationWSubVendor=0x80 wSubDevice=1 wSubAux=0x40 For PIODriverInitPIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAux D56/D24Printf\nThrer are %d Piopiso Cards in this PC,wBoards OME-PISO-P32C32 Enable all D/I/O operations of card0 PIOGetConfigAddressSpaceEnable all D/I/O operations of card1 ShowPIOPISO ShowPIOPISOwSubVendor,wSubDevice,wSubAuxAssignment of I/O Address Slot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07I/O Address Map Address Read WriteAUX Control Register RESET\ Control RegisterAUX data Register INT Mask Control Register Aux Status RegisterInterrupt Polarity Control Register 7 I/O Selection Control RegisterRead/Write 8-bit data Register How to install software & utility? Demo programPiopiso PIOPISO.EXE for Windows DEMO1 DEMO2 DEMO3 COUNT=0COUNT++ DEMO4 COUNT++ DEMO5 PC3CNTL1=CNTL2=CNTL3=CNTL4=0 Page WARRANTY/DISCLAIMER Temperature