Omega Vehicle Security OME-PIO-D56 manual Pin Assignment, All signals are TTL compatible

Page 26

2.6Pin Assignment

CON3: 37 pin of D-type female connector.

Pin Number	Description	Pin Number	Description
1	N.C.	20	VCC
2	N.C.	21	GND
3	P1B7	22	P2C7
4	P1B6	23	P2C6
5	P1B5	24	P2C5
6	P1B4	25	P2C4
7	P1B3	26	P2C3
8	P1B2	27	P2C2
9	P1B1	28	P2C1
10	P1B0	29	P2C0
11	GND	30	P0A7
12	N.C.	31	P0A6
13	GND	32	P0A5
14	N.C.	33	P0A4
15	GND	34	P0A3
16	N.C.	35	P0A2
17	GND	36	P0A1
18	VCC	37	P0A0
19	GND	XXXXXXX	This pin not available

All signals are TTL compatible.

OME-PIO-D56/PIO-D24 User Manual (Ver.2.1, Oct/2003, PPH-005-21)

---- 24

Image 26

Contents User’sGuide Benelux CanadaMexico Czech RepublicOME-PIO-D56/D24 Table of Contents Features IntroductionOptions SpecificationsOrder Description OME-PISO-series cost-effective generation, isolated cards Product ChecklistPCI Data Acquisition Family Hardware configuration Board Layout1 DI/DO Port Architecture CON3 I/O Port LocationEnabling I/O Operation Select Sec RESET\ Sec DI Port Architecture CON2 Do Port Architecture CON1 Make sure the initial level is High or Low If INT signal is Low now Æ select the non-inverted inputInterrupt Operation Interrupt Block Diagram of OME-PIO D56/D24 Interrupt output signal of OME-PIO-D56/OME-PIO-D24, INT\ isINTCHAN0/1/2/3 Initialhigh, activelow Interrupt source COUNTL++Initiallow, activehigh Interrupt source Muliti-Interrupt Source PC0 PC1 PC2 PC3Read all interrupt state OME-DN-37 Daughter BoardsOME-DB-37 OME-DB-8125OME-ADP-20/PCI OME-DB-24PD Isolated Input Board OME-DB-24RD Relay Board OME-DB-24PRD, OME-DB-24POR, OME DB-24C Daughter Board Comparison Table All signals are TTL compatible Pin AssignmentDI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 DI9 PIO/PISO identification information How to Find the I/O AddressResource-allocated information PC’s physical slot informationWSubVendor=0x80 wSubDevice=1 wSubAux=0x40 For PIODriverInitPIODriverInit&wBoards, wSubVendor,wSubDevice,wSubAux D56/D24Printf\nThrer are %d Piopiso Cards in this PC,wBoards OME-PISO-P32C32 Enable all D/I/O operations of card1 PIOGetConfigAddressSpaceEnable all D/I/O operations of card0 ShowPIOPISO ShowPIOPISOwSubVendor,wSubDevice,wSubAuxAssignment of I/O Address Slot5 0x0A Slot6 0x08 Slot7 0x09 Slot8 0x07I/O Address Map Address Read WriteAUX data Register RESET\ Control RegisterAUX Control Register INT Mask Control Register Aux Status RegisterInterrupt Polarity Control Register 7 I/O Selection Control RegisterRead/Write 8-bit data Register How to install software & utility? Demo programPiopiso PIOPISO.EXE for Windows DEMO1 DEMO2 DEMO3 COUNT=0COUNT++ DEMO4 COUNT++ DEMO5 PC3CNTL1=CNTL2=CNTL3=CNTL4=0 Page WARRANTY/DISCLAIMER Temperature