NetComm V110 manual Others, Enable Auto Configuration. Defaultoff

Page 44

Others

The others menu contains the following sub menus :

Auto Configuration Settings

You can enable/disable the auto configuration/provisioning setting in this page.

The ATA allows for provisioning and remote upgrade. Provisioning is achieved through configuration profiles transferred to the device via TFTP, HTTP or FTP. The ATA can be configured to update its VoIP Configuration from a remote profile on power up or reboot.

Options	Description

Auto Configuration	Enable Auto Configuration. (Default:off)

TFTP Server	Enter IP or Host Name of TFTP Server.

HTTP Server	Enter IP or Host Name of HTTP Server.

HTTP Path	Enter the path where the provisioning file is located.

FTP Server	Enter IP or Host Name of FTP Server.

FTP Username	Enter Username which provided by FTP Server.

FTP Password	Enter Password which provided by FTP Server.

File Path	Enter the path where the provisioning file is located.

V110,V2�10P,V2�11,V220� User Guide	YML881Rev1
44	www.netcomm.com.au

Image 44

Contents User Guide Page Welcome to the Wonderful World of VoIP VoIP ATA Features Package Contents Minimum System RequirementsReset Getting to know your NetComm V2xx ATAPorts and Buttons Port / Button DescriptionLED Indicators PWRSIP ETHDhcp Default SettingsRestoring Factory Defaults Hardware Installation V211 and V210PV110 V220 V110,V210P,V211,V220 User Guide Software Configuration Easy Setup Utility for Windows OnlyConfiguration via a web browser Accessing the web configurationWAN Configuration MAC Static IP ConfigurationOption Description YML881Rev1 Ethernet MAC address of the WAN interface. Optional Dhcp ModeYour Internet Service Provider ISP. Optional PPPoE Client Mode User NameVoIP Configuration Field Description Advanced Configuration Status System InformationNetwork Status VoIP StatusConfiguration WANOptions Description VoIP SIP Setting RTP Port Base port to receive RTP packets. Default Auth NameUse DNS SRV Support DNS SRVCodec Settings V110,V210P,V211,V220 User Guide URL Phone Book ConfigurationPhone Book Add New Phone Example 2 Position 1, Name ip address 10.32, Number 001, URLYML881Rev1 Phone Setting IP/ONYML881Rev1 V110,V210P,V211,V220 User Guide Volume Setting function To set the volume for on your handsetV211 only is to set the Pstn volume out DND AlwaysV110,V210P,V211,V220 User Guide Enter the correct PIN Code 1234, then press # How to Use VoIP to Pstn Call Call in via VoIPHow to Use Pstn to VoIP Call Call in via Pstn CID Type Enable to detect the Caller ID Type Single Caller ID Enable to detect Single Caller IDEnable to detect the Caller ID without time 2,3,4,5,6,7,8,9 Wildcard Drop PrefixDialed V110,V210P,V211,V220 User Guide YML881Rev1 Switch on to enable T.38 fax support Port Default isAuto Dial Time function FAXSupport Enable Auto Configuration. Defaultoff OthersYML881Rev1 Default Supports the proprietary implementationWALKERSUN2 Computer’s MAC that was originally set up for such an ISPOptions Description MAC Clone Ddns 110, V2 10P, V2 11, V220 User Guide Vlan Settings CFIDefault page is Page1. There are 3 pages, Page 1 to Virtual ServerNum Mapping 23 that can be setSeen from the WAN side Add the new Server which you configuredAdd Virtual Server Well Known TCP/UDP Ports UDP TCPSmtp POP3Sntp Settings If the primary server becomes unreachableAlarm Settings Save Settings/Reboot System AuthoritySystem Reset factory defaultFirmware Update Auto Update Update viaServer TFTP, FTP or Http FirmwareNotify Only Auto Update Procedure Displays the next update or check timeBe noted AutomaticallyIVR Interface for VoIP Gateway Group IVR Action IVR Menu Choice ParametersHow to make a phone call Call FeaturesDial a VoIP Phone call Dial a Pstn Phone call V210P/V211Call Hold Way ConferencingCall Waiting Common problem and solutions No power to the ATAPlease ensure that the power cable is connected correctly ETH light is offAppendix a Glossary ATAProduct Warranty Limitations of WarrantyV110,V210P,V211,V220 User Guide Your ADSL2+ connection Product Warranty Contact Information Email support@netcomm.com.au