NetComm V110 manual Auth Name, Use DNS SRV, Support DNS SRV, SIP Port

Page 26

User Name

Your VoIP number. This number is assigned by your VoIP service provider.

 

 

Auth Name

The authentication username assigned by your VoIP service provider. This can be

 

different to your VoIP number.

 

 

Auth Password

The authentication password provided by your VoIP service provider.

 

 

Subscribe for MWI

When enabled the Subscribe for Message Waiting Indication will be sent periodically.

 

 

Status

Indicates if the VoIP Gateway is registered to your VSP. If “Registered” is shown, you can

 

make and receive calls via your VoIP service provider. If the VoIP gateway reports “not

 

registered”, check the SIP Service Provider settings above and try again.

 

 

SIP Expiry Time

This setting specifies a recommendation to the SIP server on the re-registration interval.

 

Increasing this time will send less registration traffic, but can cause other issues.

 

 

Use DNS SRV

When DNS SRV is switched on, the VoIP Gateway will look up DNS SRV records and

 

register with the server with the highest priority. DNS SRV can provide redundancy if the

 

primary SIP server becomes unreachable. Please check with your VSP to find out if they

 

support DNS SRV.

 

 

Port Setting

You can configure the SIP and RTP port number in this page. Please leave as default unless otherwise specified by your VSP.

Options

Description

 

 

SIP Port

The port on the SIP server that receives requests from the ATA. Default: 5060.

 

 

RTP Port

The base port to receive RTP packets. Default: 60000.

 

 

V110,V210P,V211,V220User Guide

YML881Rev1

26

www.netcomm.com.au

Image 26
Contents User Guide Page Welcome to the Wonderful World of VoIP VoIP ATA Features Package Contents Minimum System RequirementsPorts and Buttons ResetGetting to know your NetComm V2xx ATA Port / Button DescriptionSIP LED IndicatorsPWR ETHDhcp Default SettingsRestoring Factory Defaults Hardware Installation V211 and V210PV110 V220 V110,V210P,V211,V220 User Guide Software Configuration Easy Setup Utility for Windows OnlyConfiguration via a web browser Accessing the web configurationWAN Configuration MAC Static IP ConfigurationOption Description YML881Rev1 Ethernet MAC address of the WAN interface. Optional Dhcp ModeYour Internet Service Provider ISP. Optional PPPoE Client Mode User NameVoIP Configuration Field Description Advanced Configuration Network Status StatusSystem Information VoIP StatusConfiguration WANOptions Description VoIP SIP Setting Use DNS SRV RTP Port Base port to receive RTP packets. DefaultAuth Name Support DNS SRVCodec Settings V110,V210P,V211,V220 User Guide URL Phone Book ConfigurationPhone Book Add New Phone Example 2 Position 1, Name ip address 10.32, Number 001, URLYML881Rev1 Phone Setting IP/ONYML881Rev1 V110,V210P,V211,V220 User Guide V211 only is to set the Pstn volume out Volume Setting functionTo set the volume for on your handset DND AlwaysV110,V210P,V211,V220 User Guide Enter the correct PIN Code 1234, then press # How to Use VoIP to Pstn Call Call in via VoIPHow to Use Pstn to VoIP Call Call in via Pstn CID Type Enable to detect the Caller ID Type Single Caller ID Enable to detect Single Caller IDEnable to detect the Caller ID without time 2,3,4,5,6,7,8,9 Wildcard Drop PrefixDialed V110,V210P,V211,V220 User Guide YML881Rev1 Auto Dial Time function Switch on to enable T.38 fax supportPort Default is FAXSupport Enable Auto Configuration. Defaultoff OthersYML881Rev1 Default Supports the proprietary implementationWALKERSUN2 Computer’s MAC that was originally set up for such an ISPOptions Description MAC Clone Ddns 110, V2 10P, V2 11, V220 User Guide Vlan Settings CFINum Default page is Page1. There are 3 pages, Page 1 toVirtual Server Mapping 23 that can be setSeen from the WAN side Add the new Server which you configuredAdd Virtual Server Smtp Well Known TCP/UDP PortsUDP TCP POP3Sntp Settings If the primary server becomes unreachableAlarm Settings Save Settings/Reboot System AuthoritySystem Reset factory defaultFirmware Update Server TFTP, FTP or Http Auto UpdateUpdate via FirmwareBe noted Notify Only Auto Update ProcedureDisplays the next update or check time AutomaticallyIVR Interface for VoIP Gateway Group IVR Action IVR Menu Choice ParametersDial a VoIP Phone call How to make a phone callCall Features Dial a Pstn Phone call V210P/V211Call Hold Way ConferencingCall Waiting Please ensure that the power cable is connected correctly Common problem and solutionsNo power to the ATA ETH light is offAppendix a Glossary ATAProduct Warranty Limitations of WarrantyV110,V210P,V211,V220 User Guide Your ADSL2+ connection Product Warranty Contact Information Email support@netcomm.com.au