NetComm V110 manual Default Settings, Restoring Factory Defaults, Dhcp

Page 8

Default Settings

LAN (Management)

Static IP Address:

192.168.22.1

 

 

Subnet Mask:

255.255.255.0

 

 

Default Gateway:

blank

 

 

WAN (Internet)

 

 

 

WAN mode:

DHCP

 

 

Modem Access

 

 

 

Username:

admin

 

 

Password:

admin

 

 

Many configuration changes made using the web interface will only become active after clicking the Save & Reboot button on the Save Savings / Reboot page in the web configuration page.

Note: Certain voice parameters do not require a Save & Reboot to take effect. These Voice Parameters will take effect on the next voice call after the Voice Parameter is entered and submitted. However, if Save & Reboot is not done, then these Voice Parameters will not be saved over a power cycle. The Voice Parameters that can be changed “on the fly” are noted in the respective sections.

Restoring Factory Defaults

The reset button will reset the ATA to its factory default configuration. Occasions may present themselves where you need to restore the factory default settings on your ATA. Typical situations are:

You have lost your password and unable to login to the ATA;

You have purchased the router from someone else and need to reconfigure the device.

You are asked to perform a factory reset by a member of the excellent NetComm Support Staff.

In order to restore your router to its factory default settings, please follow these steps:

Ensure that the ATA is powered on (for at least 20 seconds).

Use a paper clip or a pencil tip to depress the reset button for ten seconds and release. At this point, the reset is in progress. Do not power off the unit at this point.

After the ATA reboots, the default settings are now restored. This entire process takes several minutes to complete.

Once you have reset the ATA to its default settings you will be able to access the device’s web configuration using http://192.168.22.1 with username “admin” and password “admin”.

V110,V210P,V211,V220User Guide

YML881Rev1

 

www.netcomm.com.au

Image 8
Contents User Guide Page Welcome to the Wonderful World of VoIP VoIP ATA Features Package Contents Minimum System RequirementsReset Getting to know your NetComm V2xx ATAPorts and Buttons Port / Button DescriptionLED Indicators PWRSIP ETHDhcp Default SettingsRestoring Factory Defaults Hardware Installation V211 and V210PV110 V220 V110,V210P,V211,V220 User Guide Software Configuration Easy Setup Utility for Windows OnlyConfiguration via a web browser Accessing the web configurationWAN Configuration MAC Static IP ConfigurationOption Description YML881Rev1 Ethernet MAC address of the WAN interface. Optional Dhcp ModeYour Internet Service Provider ISP. Optional PPPoE Client Mode User NameVoIP Configuration Field Description Advanced Configuration Status System InformationNetwork Status VoIP StatusConfiguration WANOptions Description VoIP SIP Setting RTP Port Base port to receive RTP packets. Default Auth NameUse DNS SRV Support DNS SRVCodec Settings V110,V210P,V211,V220 User Guide URL Phone Book ConfigurationPhone Book Add New Phone Example 2 Position 1, Name ip address 10.32, Number 001, URLYML881Rev1 Phone Setting IP/ONYML881Rev1 V110,V210P,V211,V220 User Guide Volume Setting function To set the volume for on your handsetV211 only is to set the Pstn volume out DND AlwaysV110,V210P,V211,V220 User Guide Enter the correct PIN Code 1234, then press # How to Use VoIP to Pstn Call Call in via VoIPHow to Use Pstn to VoIP Call Call in via Pstn CID Type Enable to detect the Caller ID Type Single Caller ID Enable to detect Single Caller IDEnable to detect the Caller ID without time 2,3,4,5,6,7,8,9 Wildcard Drop PrefixDialed V110,V210P,V211,V220 User Guide YML881Rev1 Switch on to enable T.38 fax support Port Default isAuto Dial Time function FAXSupport Enable Auto Configuration. Defaultoff OthersYML881Rev1 Default Supports the proprietary implementationWALKERSUN2 Computer’s MAC that was originally set up for such an ISPOptions Description MAC Clone Ddns 110, V2 10P, V2 11, V220 User Guide Vlan Settings CFIDefault page is Page1. There are 3 pages, Page 1 to Virtual ServerNum Mapping 23 that can be setSeen from the WAN side Add the new Server which you configuredAdd Virtual Server Well Known TCP/UDP Ports UDP TCPSmtp POP3Sntp Settings If the primary server becomes unreachableAlarm Settings Save Settings/Reboot System AuthoritySystem Reset factory defaultFirmware Update Auto Update Update viaServer TFTP, FTP or Http FirmwareNotify Only Auto Update Procedure Displays the next update or check timeBe noted AutomaticallyIVR Interface for VoIP Gateway Group IVR Action IVR Menu Choice ParametersHow to make a phone call Call FeaturesDial a VoIP Phone call Dial a Pstn Phone call V210P/V211Call Hold Way ConferencingCall Waiting Common problem and solutions No power to the ATAPlease ensure that the power cable is connected correctly ETH light is offAppendix a Glossary ATAProduct Warranty Limitations of WarrantyV110,V210P,V211,V220 User Guide Your ADSL2+ connection Product Warranty Contact Information Email support@netcomm.com.au