Multi-Tech Systems MT3334SMI manual +Fpts, +Frbc, +Frel, +Fspl, +Ftbc, +Fcfr, +Fcon, +Fcsi

Page 48

ModemModule Developer’s Guide

+FPTS	Page Transfer Status
Command syntax:		+FPTS=<ppr>
		1: MCF Page good
		2: RTN Page good; retrain requested
		3: RTP Page good; retrain requested.

+FRBC	Phase C Receive Data Block Size
Command syntax:		+FRBC=<value>
		0: Stream mode, Phase C data is terminated by <DLE><ETX>.
+FREL	Phase C Received EOL Alignment
Command syntax:		+FREL=<value>
		0: Indicates that EOL patterns are aligned as received (Default).
		1: Indicates that the last received bits of EOL patterns are byte aligned by
		DCE, with necessary zero fill bits inserted. There are two 2-byte patterns:
		+FBOR	binary EOL pattern
		0	0000xxxx	10000000
		1	xxxx0000	00000001

xxxx represents previous data bits, zero bits, or other leading data.

+FSPL	Request to Poll
Command syntax:		+FSPL=<value>
		0: Indicates that the DTE does not want to poll.
+FTBC	Phase C Transmit Data Block Size
Command syntax:		+FTBC=<value>
		0: Stream mode, Phase C data is terminated by <DLE><ETX>.
+FCFR	Indicates Confirmation to Receive
Syntax:		+FCFR
Usage:	Indicates the reception of an acceptable TCF training burst and valid DCS signal
	from the remotemachine.
+FCON	Facsimile Connection Response
Syntax:		+FCON
Usage:	Indicates connection with a FAX machine. Generated in response to an originate
	command or answer command.
+FCSI	Reports the Remote ID
Syntax:		+FCSI:”<CSI ID string>”
Usage:	Reports the called station’s ID.
+FDCS	Reports DCS Frame Information
Syntax:		+FDCS:VR,BR,WD,LN,DF,EC,BF,ST
Usage:	Reports negotiated parameters for the current session. The subparameters are
	described in the +FDCS command description.

48

MT3334SMI

Image 48

Contents Model MT3334SMI Evaluation Kit Data/Fax Socketed ModemRevision Description PatentsContents Index Introduction and Description Features IntroductionProduct Description ModemModule Developer’s GuideTechnical Specifications Introduction and Description1200 bps Physical Dimensions MT3334SMI Physical DimensionsTest/Demo Board Specifications DS1LED1-LED4 Test/Demo Board Block Diagram MT3334SMI Test/Demo Board Block DiagramMT3334SMI Pin-out MT3334SMI PinoutTypical Application MT3334SMI Design Considerations Hardware ConsiderationsPC Board Layout Considerations Calculating Z for Tip and Ring TracesRecommended Transceiver MT3334SMI Placement KeyQty Name Description Telecom Labeling Requirements FCC PartReregistration Industry Canada CS-03Multiple Listing AT Commands, S-Registers, and Result Codes Repeat Last Command AnswerAT Commands, S-Registers, and Result Codes Monitor Speaker Volume Monitor Speaker ModeReturn Online to Data Mode Result Codes Enable/DisableModem Reset Sr? Read Register ValueTone Dialing Result Code FormatCommand &Fn Load Factory Settings Asynchronous Communications ModeDisplay Current Settings Store Current ConfigurationCommand &Zy=x Store Dialing Command \An Select Maximum MNP Block Size\Bn Transmit Break \Jn Data Buffer Control\Nn Error Correction Mode Selection \Tn Inactivity Timer\Qn Flow Control Selection \Vn Protocol Result CodeCommand %DCn AT Command Control Command %En Fallback and Fall Forward ControlCommand +ES=n Enable Synchronous Buffered Mode Enter Setup PasswordRegister Unit Range Default Description RegistersS43 Result Codes Terse Verbose DescriptionClass 1 Fax Commands Class 1 Fax Command Summary Command DescriptionClass 1 Fax Commands Fax MOD Modulation Parameter Values CommandFunction Display Current Class Values Default Data modem Result Code MeaningModemModule Developer’s Guide Command Function Select Service Class Values Default Data modeFunction Class 1 Fax Commands +FRS=? Enter+FRM=? Enter Flow Control Result CodesSample Sessions Action by Command Respone Local Modem Remote PC AT+FRH=3 No Carrier ModemModule Developer’s Guide Class 2 Fax Commands Class 2 Fax Command Implementation Class 2 Fax Commands EIA SP-2388 August+FAA +FAXERR+FBOR +FCQ+FCR +FDCC Fax Capability Parameters+FDCS Current Session Results+FDFFC Data Compression Format Conversion+FDIS Current Session Parameters+FDR +FDT+FECM +FET+FK +FLID+FLNFC +FLPL+FPTS +FRBC+FREL +FSPL+FHNG +FTSIMT3334SMI Remote Configuration Basic Procedure SetupChanging the Setup Password ModemModule User GuideRemote Configuration Changing the Remote Escape CharacterMT3334SMI Troubleshooting Test procedure Local Analog Loopback Test V.54 LoopTroubleshooting Remote Digital Loopback Test V.54 LoopLocal Digital Loopback Test V.54 Loop Local digital loopback testUpgrade Procedure Upgrade Overview Identify the Modem FirmwareIdentify the Current Firmware Version Multi-Tech Web SiteDownload the Upgrade File Upgrade ProcedureMulti-Tech BBS Extract the Upgrade Files Use FlashPro to Upgrade Modem FirmwareRestore Your Parameters Clear Your Stored ParamentersAppendixes MT3334SMI FCC FAX Update International Modem RestrictionsCanadian Limitations Notice AppendixesEMC, Safety and Terminal Directive Compliance European Directives User Guide StatementNew Zealand Telecom Warning Notice Appendix B Multi-Tech Flash Programming Protocol IntroductionProgramming the Modem Handshake SequenceOther supported boot code commands Other programming concernsModemModule Developer’s Guide Program Sequence Intel Hex Format Data RecordXxxx Extended Address Record End of File RecordEeee Index IndexMT3334SM MT3334SMI MT3334SM