Multi-Tech Systems MT3334SMI manual Class 1 Fax Command Summary, Command Description

Page 32

ModemModule Developer’s Guide

Introduction

The Service Class 1 standard (EIA/TIA-578) defines the commands that a PC user may issue to configure and control a fax/data modem, and the responses (result codes) that the fax/data modem may issue in response to those commands.

The Class 1 standard provides the basic services needed to support Group 3 fax operation. Support of the 1988 CCITT (ITU-T) T.30 recommended procedures for session management and the T.4 recommendation for image data handling are required at the PC.

Service Class 1 provides the following services (as required, or optional in Group 3 facsimile operation):

•Connection (originate and answer),

•Waiting and silence detection,

•Data transmission and reception (data transfer),

•HDLC (High-level Data Link Control) data framing/transparency/error detection, and

•Message generation/response.

HDLC is an ISO standard, bit-oriented data communications protocol. HDLC control information is consistently placed, and specific control bit patterns are considerably different than those used as data, providing a largely error-free protocol.

Class 1 Fax Command Summary

The ModemModule Fax Class 1 enhancements are implemented with six AT+F (for Fax) commands. The +FTM, +FRM, +FTH, and +FRH commands must be entered as the last command in the command string (i.e., the last command on the command line). The +FTS and the +FRS commands can be entered anywhere in the command string.

Command Description

+FCLASS? Display Current Class

+FCLASS=? Display Service Class Capabilities +FCLASS=<> Select Service Class

+FTS=<time> Stop tranmission and pause (10 ms intervals, 0-255)

+FTS=? Display the valid +FTS=<time> range (0-255) +FRS=<time> Wait for silence (10 ms intervals, 0-255)

+FRS=? Display the valid +FRS=<time> range +FTM=<MOD> Transmit data with specified <MOD> carrier

+FTM=? Display the valid +FTM=<MOD> carrier range +FRM=<MOD> Receive data with specified <MOD> carrier

+FRM=? Display the valid +FRM=<MOD> carrier range +FTH=<MOD> Transmit HDLC data with specified <MOD> carrier

+FTH=? Display the valid +FTH=<MOD> carrier range +FRH=<MOD> Receive HDLC data with specified <MOD> carrier

+FRH=? Display the valid +FRH=<MOD> carrier range

If entering multiple commands on the command line, use semicolons between commands. These +F commands are defined in the following sections. The <MOD> parameter may take on the following values.

32

MT3334SMI

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Model MT3334SMI Evaluation Kit Data/Fax Socketed ModemRevision Description PatentsContents Index Introduction and Description Features IntroductionProduct Description ModemModule Developer’s GuideTechnical Specifications Introduction and Description1200 bps Physical Dimensions MT3334SMI Physical DimensionsLED1-LED4 Test/Demo Board SpecificationsDS1 Test/Demo Board Block Diagram MT3334SMI Test/Demo Board Block DiagramMT3334SMI Pin-out MT3334SMI PinoutTypical Application MT3334SMI Design Considerations Hardware ConsiderationsRecommended Transceiver PC Board Layout ConsiderationsCalculating Z for Tip and Ring Traces Qty Name Description MT3334SMI PlacementKey Telecom Labeling Requirements FCC PartMultiple Listing ReregistrationIndustry Canada CS-03 AT Commands, S-Registers, and Result Codes Repeat Last Command AnswerAT Commands, S-Registers, and Result Codes Monitor Speaker Volume Monitor Speaker ModeReturn Online to Data Mode Result Codes Enable/DisableModem Reset Sr? Read Register ValueTone Dialing Result Code FormatCommand &Fn Load Factory Settings Asynchronous Communications ModeDisplay Current Settings Store Current ConfigurationCommand &Zy=x Store Dialing Command \An Select Maximum MNP Block Size\Bn Transmit Break \Jn Data Buffer Control\Nn Error Correction Mode Selection \Tn Inactivity Timer\Qn Flow Control Selection \Vn Protocol Result CodeCommand %DCn AT Command Control Command %En Fallback and Fall Forward ControlCommand +ES=n Enable Synchronous Buffered Mode Enter Setup PasswordRegister Unit Range Default Description RegistersS43 Result Codes Terse Verbose DescriptionClass 1 Fax Commands Class 1 Fax Command Summary Command DescriptionClass 1 Fax Commands Fax MOD Modulation Parameter Values CommandFunction Display Current Class Values Default Data modem Result Code MeaningFunction ModemModule Developer’s Guide CommandFunction Select Service Class Values Default Data mode Class 1 Fax Commands +FRS=? Enter+FRM=? Enter Sample Sessions Flow ControlResult Codes Action by Command Respone Local Modem Remote PC AT+FRH=3 No Carrier ModemModule Developer’s Guide Class 2 Fax Commands Class 2 Fax Command Implementation Class 2 Fax Commands EIA SP-2388 August+FAA +FAXERR+FCR +FBOR+FCQ +FDCC Fax Capability Parameters+FDCS Current Session Results+FDFFC Data Compression Format Conversion+FDIS Current Session Parameters+FDR +FDT+FECM +FET+FK +FLID+FLNFC +FLPL+FPTS +FRBC+FREL +FSPL+FHNG +FTSIMT3334SMI Remote Configuration Basic Procedure SetupChanging the Setup Password ModemModule User GuideRemote Configuration Changing the Remote Escape CharacterMT3334SMI Troubleshooting Test procedure Local Analog Loopback Test V.54 LoopTroubleshooting Remote Digital Loopback Test V.54 LoopLocal Digital Loopback Test V.54 Loop Local digital loopback testUpgrade Procedure Upgrade Overview Identify the Modem FirmwareIdentify the Current Firmware Version Multi-Tech Web SiteMulti-Tech BBS Download the Upgrade FileUpgrade Procedure Extract the Upgrade Files Use FlashPro to Upgrade Modem FirmwareRestore Your Parameters Clear Your Stored ParamentersAppendixes MT3334SMI FCC FAX Update International Modem RestrictionsCanadian Limitations Notice AppendixesNew Zealand Telecom Warning Notice EMC, Safety and Terminal Directive ComplianceEuropean Directives User Guide Statement Appendix B Multi-Tech Flash Programming Protocol IntroductionProgramming the Modem Handshake SequenceModemModule Developer’s Guide Program Sequence Other supported boot code commandsOther programming concerns Xxxx Intel Hex FormatData Record Eeee Extended Address RecordEnd of File Record Index IndexMT3334SM MT3334SMI MT3334SM
Top Page Image Contents