Multi-Tech Systems MT3334SMI manual +Fhng, +Ftsi

Page 49

	Chapter 4 - Class 2 Fax Commands

+FDIS	Reports DIS Frame Information
Syntax:	+FDIS:VR,BR,WD,LN,DF,EC,BF,ST
Usage:	Reports remote FAX capabilities and intentions. The subparameters are described in
	the +FDCS command description.
+FET	Post Page Message Response
Syntax:	+FET:<ppm>
Usage:	Generated by the receiving modem after the end of Phase C reception, on receipt of
	the postpage message from the transmitting station. The <ppm> codes are
	described in the +FET command description.
+FHNG	Call Termination with Status
Syntax:	+FHNG:<hang-up status code>
Usage:	Indicates that the call has been terminated. The <hang-up status code> values are
	described in the +FAXERR command description.
+FPTS	Receive/Transmit Page Transfer Status
Syntax:	+FPTS:<ppr>
Usage:	Reports a <ppr> number representing the copy quality and related post page
	message. The valid <ppr> values are defined in the +FPTS command description.
+FTSI	Report the Remote ID
Syntax:	+FTSI:”<TSI ID string>”
Usage:	Reports the transmitting station’s ID.

For More Information

To obtain Data and Fax specifications and standards (e.g., Class 1 documents (EIA/TIA-578), and Class 2 documents - EIA/TIA Project Number 2388, Async Fax DCE Control Standard Service Class 2, TR29.2), contact:

Telecommunications Industry Association (TIA) 2500 Wilson Boulevard

Suite 300 Arlington, VA 22201 Ph: 703-907-7700 http://www.tiaonline.org/

The ITU is the leading publisher of international telecommunication standards. For further information contact sales@itu.int or http://www.itu.int/publications/index.html

Global Engineering maintains extensive collections of documents from more than 400 standards- developing organizations worldwide, including: TIA/EIA-578 - Class 1 documents, TIA/EIA-592 - Class 2 documents.

EIA TSB 43 (corrections to TIA/EIA-578), EIA SP 2987 (draft of changes to TIA/EIA-578), and CCITT

v7.3 - T.1-T.90 standards (including (T.4 and T.30). Contact:

Global Engineering Documents 800-854-7179 (phone)

303-792-2192 (fax) http://global.ihs.com/

MT3334SMI

49

Image 49

Contents Data/Fax Socketed Modem Model MT3334SMI Evaluation KitPatents Revision DescriptionContents Index Introduction and Description Introduction FeaturesProduct Description ModemModule Developer’s GuideIntroduction and Description Technical Specifications1200 bps MT3334SMI Physical Dimensions Physical DimensionsDS1 Test/Demo Board SpecificationsLED1-LED4 MT3334SMI Test/Demo Board Block Diagram Test/Demo Board Block DiagramMT3334SMI Pinout MT3334SMI Pin-outTypical Application Hardware Considerations MT3334SMI Design ConsiderationsCalculating Z for Tip and Ring Traces PC Board Layout ConsiderationsRecommended Transceiver Key MT3334SMI PlacementQty Name Description FCC Part Telecom Labeling RequirementsIndustry Canada CS-03 ReregistrationMultiple Listing AT Commands, S-Registers, and Result Codes Answer Repeat Last CommandAT Commands, S-Registers, and Result Codes Monitor Speaker Mode Monitor Speaker VolumeReturn Online to Data Mode Result Codes Enable/DisableSr? Read Register Value Modem ResetTone Dialing Result Code FormatAsynchronous Communications Mode Command &Fn Load Factory SettingsDisplay Current Settings Store Current Configuration\An Select Maximum MNP Block Size Command &Zy=x Store Dialing Command\Bn Transmit Break \Jn Data Buffer Control\Tn Inactivity Timer \Nn Error Correction Mode Selection\Qn Flow Control Selection \Vn Protocol Result CodeCommand %En Fallback and Fall Forward Control Command %DCn AT Command ControlCommand +ES=n Enable Synchronous Buffered Mode Enter Setup PasswordRegisters Register Unit Range Default DescriptionS43 Terse Verbose Description Result CodesClass 1 Fax Commands Command Description Class 1 Fax Command SummaryCommand Class 1 Fax Commands Fax MOD Modulation Parameter ValuesFunction Display Current Class Values Default Data modem Result Code MeaningFunction Select Service Class Values Default Data mode ModemModule Developer’s Guide CommandFunction +FRS=? Enter Class 1 Fax Commands+FRM=? Enter Result Codes Flow ControlSample Sessions Action by Command Respone Local Modem Remote PC AT+FRH=3 No Carrier ModemModule Developer’s Guide Class 2 Fax Commands Class 2 Fax Commands EIA SP-2388 August Class 2 Fax Command Implementation+FAA +FAXERR+FCQ +FBOR+FCR Fax Capability Parameters +FDCC+FDCS Current Session ResultsData Compression Format Conversion +FDFFC+FDIS Current Session Parameters+FDT +FDR+FECM +FET+FLID +FK+FLNFC +FLPL+FRBC +FPTS+FREL +FSPL+FTSI +FHNGMT3334SMI Remote Configuration Setup Basic ProcedureChanging the Setup Password ModemModule User GuideChanging the Remote Escape Character Remote ConfigurationMT3334SMI Troubleshooting Local Analog Loopback Test V.54 Loop Test procedureRemote Digital Loopback Test V.54 Loop TroubleshootingLocal digital loopback test Local Digital Loopback Test V.54 LoopUpgrade Procedure Identify the Modem Firmware Upgrade OverviewIdentify the Current Firmware Version Multi-Tech Web SiteUpgrade Procedure Download the Upgrade FileMulti-Tech BBS Use FlashPro to Upgrade Modem Firmware Extract the Upgrade FilesRestore Your Parameters Clear Your Stored ParamentersAppendixes MT3334SMI International Modem Restrictions FCC FAX UpdateCanadian Limitations Notice AppendixesEuropean Directives User Guide Statement EMC, Safety and Terminal Directive ComplianceNew Zealand Telecom Warning Notice Introduction Appendix B Multi-Tech Flash Programming ProtocolProgramming the Modem Handshake SequenceOther programming concerns Other supported boot code commandsModemModule Developer’s Guide Program Sequence Data Record Intel Hex FormatXxxx End of File Record Extended Address RecordEeee Index IndexMT3334SM MT3334SMI MT3334SM