Multi-Tech Systems MT2834BLR, MT2834BR manual Tone

Page 42

 

Chapter 4 - Commands

 

 

 

 

DEFAULT:

X0

DESCRIPTION:

X0 selects Basic Result Codes (w/o CONNECT 1200,

 

CONNECT 2400).

 

X1 selects Extended Result Codes (w/CONNECT 1200,

 

CONNECT 2400).

 

X2 selects Standard AT Command set with NO DIAL

 

TONE.

 

X3 selects Standard AT Command set with BUSY.

 

X4 selects Standard AT Command set with NO DIAL

 

TONE and BUSY.

COMMAND:

#Xn

VALUES:

n = 0 or 1

DEFAULT:

#X0

DESCRIPTION:

#X0 selects single XOFF character sent until XON level

 

returns.

 

#X1 selects multiple XOFF characters after buffer level is

 

full.

COMMAND:

Yn

VALUES:

n = 0 or 1

DEFAULT:

Y0

DESCRIPTION:

Y0 disables sending or responding to long space “break”.

 

Y1 enables sending or responding to long space “breaks”.

COMMAND:

Z

VALUES:

n/a

DEFAULT:

n/a

DESCRIPTION:

All configuration parameters are reset to default values.

COMMAND:

, (Comma)

VALUES:

n/a

DEFAULT:

n/a

DESCRIPTION:

Causes pause during dialing.

COMMAND:

;(Semi-Colon)

VALUES:

n/a

DEFAULT:

n/a

DESCRIPTION:

Causes return to Command Mode after dialing.

COMMAND:

! (Exclamation)

VALUES:

n/a

DEFAULT:

n/a

DESCRIPTION:

Causes modem to flash On-Hook.

COMMAND:

@

VALUES:

n/a

42

Image 42
Contents User Guide Revision Date Description Contents AT Commands and S-Register Summary Introduction Features IntroductionHow to Use This Manual Installation Serial Cable PreliminariesCard Cage Telephone LineInstallation PC Board Controls DIP-Switch Settings Switch Function Position EffectAnswer/Originate Originate call Async/Sync/Leased Line OOS Busy Out Toggle Switch Dip Switch Settings #13 Position EffectOut of Service/Test Jumper 2 MI/MIC Option JumperDial-Up and Leased Lines Modem LED Indicators On-Line Diagnostics Installation Serial Port Limitations How Can You Identify Your Uart Type? MSD Uart Identification, Screen Configuring Your Software Configuring Software for Your ModemPC Initialization Strings AT &F X4 S0=0 MMEW Modem Initialization Setup Changing Default Parameters Macintosh InitializationConfiguring Software for Your Computer MEW Configuration Parameters ScreenConfiguring Software for the Remote System Terminal EmulationWhen to Disable Data Compression File Transfer ProtocolsDisabling Error Correction AT &F S0=0 X4 &E14 MModem Commands Modem AT Commands Commands = 0, 1, 2 or DP0 #F2 Command Values Default = speed Q0 selects Result Codes displayed Reads value of S-Register r and displays value = 4 or Tone Callback Security Commands Command Break Atcr Values Default DescriptionCallback password with xxxxxx being callback password Remote Configuration Remote Configuration Procedures4 V.25bis Commands Password CommandsCSPs Registers Escape Code CharacterLine Feed Character S10 Carrier Loss Disconnect Delay Time S25 DTR Dropout Time Result Codes S36 Time Between DTR Inactive and Modem Off-HookTerse Verbose No Dial Tone Busy No Answer AT Commands and S-Register Summary Modem Testing Local Analog Loopback Test/V.54 Loop UuuuDigital Loopback Test/V.54 Loop 2 Local/Manual Digital Loopback Test local / manual Digital Loopback Test/V.54 Loop 2 Remote/Automatic Digital Loopback Test remote / automaticLocal Analog Loopback Test Synchronous Mode Local Analog Loopback Test Syncronous ModeDigital Loopback Test Local/Manual Synchronous Mode Digital Loopback Test Local / manual SyncronousDigital Loopback Test Remote/Automatic Synchronous Mode Digital Loopack Test remote / automatic SyncronousWarranty and Service Limited Warranty Service Tech SupportRecording Modem Information Using FlashPro to Upgrade Modem Firmware Upgrading the MT2834BRSafety Warnings Internet Babt Requirements Compliance with Babt Requirements European Low Voltage Directive Compliance with BS6789 .1 and Part Compliance with BS6328 Part Appendices Appendix a Appendix a Canadian Limitations Notice Appendix B Technical Specifications Data Rates modemFlow Control 2400 & 1200 bps Frequency Stability Index Index Index Index MNP SCC XON/XOFF S000316