Multi-Tech Systems MT2834BLR manual Result Codes, S36 Time Between DTR Inactive and Modem Off-Hook

Page 52

Chapter 4 - Commands

S36

Time Between DTR Inactive and Modem Off-Hook

Unit:	1 Second
Range:	0-255 seconds
Default:	0
Description:	Sets the time between DTR inactive (low) and the modem
	going off-hook. The DTR Busy-out feature is disabled with
	S36=0.

S37

Time Between DTR Active and Modem On-Hook

Unit:	1 Second
Range:	0-255 seconds
Default:	5
Description:	Sets the time between DTR being active and the modem
	going on-hook(not busy).

S48

Program V34 Connect Speeds

Unit:	N/A
Range:	33, 31, 28, 26, 24, 21,19,16,14,12, 96 and 48
Default:	0
Description:	Defines which speed modem connects within Enhanced
	V.34 mode scope (e.g., S48 = 21 means maximum connect
	speed is 21.6K). This register is when line conditions will
	not support higher Enhanced V.34 speeds (e.g., 33.6K,
	31.2K, 28K, 26.4K, 24K...) The modem default is a value
	of 0, which indicates a connection attempt of 33.6K.

4.3Result Codes

The MT2834BR Command mode provides you with several responses, or “Result Codes”, that can aid you in Command mode operation. These Result Codes are displayed on your video monitor.

AT&Q0	Selects Multi-Tech responses with Reliable/Compression
	modifiers. The terse result code for CONNECT 2400 is 9.
AT&Q1	selects Standard AT command set responses. The terse
	result code for CONNECT 2400 is 10.
	Table 4-1: &Q0 "Multi-Tech" Result Codes

52

Image 52

Contents User Guide Revision Date Description Contents AT Commands and S-Register Summary Introduction Features IntroductionHow to Use This Manual Installation Preliminaries Card CageSerial Cable Telephone LineInstallation PC Board Controls DIP-Switch Settings Switch Function Position EffectAnswer/Originate Originate call Async/Sync/Leased Line OOS Busy Out Toggle Switch Dip Switch Settings #13 Position EffectOut of Service/Test Jumper 2 MI/MIC Option JumperDial-Up and Leased Lines Modem LED Indicators On-Line Diagnostics Installation Serial Port Limitations How Can You Identify Your Uart Type? MSD Uart Identification, Screen Configuring Your Software Configuring Software for Your ModemPC Initialization Strings AT &F X4 S0=0 MMEW Modem Initialization Setup Changing Default Parameters Macintosh InitializationConfiguring Software for Your Computer MEW Configuration Parameters ScreenConfiguring Software for the Remote System Terminal EmulationWhen to Disable Data Compression File Transfer ProtocolsDisabling Error Correction AT &F S0=0 X4 &E14 MModem Commands Modem AT Commands Commands = 0, 1, 2 or DP0 #F2 Command Values Default = speed Q0 selects Result Codes displayed Reads value of S-Register r and displays value = 4 or Tone Callback Security Commands Command Break Atcr Values Default DescriptionCallback password with xxxxxx being callback password Remote Configuration Remote Configuration Procedures4 V.25bis Commands Password CommandsCSPs Registers Escape Code CharacterLine Feed Character S10 Carrier Loss Disconnect Delay Time S25 DTR Dropout Time Result Codes S36 Time Between DTR Inactive and Modem Off-HookTerse Verbose No Dial Tone Busy No Answer AT Commands and S-Register Summary Modem Testing Local Analog Loopback Test/V.54 Loop UuuuDigital Loopback Test/V.54 Loop 2 Local/Manual Digital Loopback Test local / manual Digital Loopback Test/V.54 Loop 2 Remote/Automatic Digital Loopback Test remote / automaticLocal Analog Loopback Test Synchronous Mode Local Analog Loopback Test Syncronous ModeDigital Loopback Test Local/Manual Synchronous Mode Digital Loopback Test Local / manual SyncronousDigital Loopback Test Remote/Automatic Synchronous Mode Digital Loopack Test remote / automatic SyncronousWarranty and Service Limited Warranty Tech Support ServiceRecording Modem Information Using FlashPro to Upgrade Modem Firmware Upgrading the MT2834BRSafety Warnings Internet Babt Requirements Compliance with Babt Requirements European Low Voltage Directive Compliance with BS6789 .1 and Part Compliance with BS6328 Part Appendices Appendix a Appendix a Canadian Limitations Notice Appendix B Technical Specifications Data Rates modemFlow Control 2400 & 1200 bps Frequency Stability Index Index Index Index MNP SCC XON/XOFF S000316