Multi-Tech Systems MT5634ZPX-PCI owner manual Port COM Interrupt Address Speed

Page 20

Owner’s Manual

5.Click the Resources tab and note the Conflicting Device list. If there is a conflict between your modem and another device in your computer, the information appears here. For help in resolving a conflict, click Start, Help, and then search the Help index for the Hardware Conflict Troubleshooter. When finished, click OK to exit the System Properties dialog box.

6.In Control Panel, double-click the Modems icon.

7.When the Modems Properties dialog box appears, click the Diagnostics tab. A list of ports and the devices installed on them appears.

8.Click the COM port where the Multi-Tech MT5634ZPX-PCI is installed. Then click More Info to make sure Windows 95 can communicate with the modem. Clicking More Info causes Windows 95 to send commands to and receive responses from the modem and to display information about the modem’s COM port.

9.Write down the modem’s port, interrupt, address, and highest speed. You will need this information to set up any legacy (nonWindows 95) communications software you install.

Port: COM __ Interrupt:_ Address:_____

Speed: _______

10.Click the General tab. Select Multi-Tech MT5634ZPX-PCI and click Properties to review the modem’s default communications settings. Do not change any settings unless you have special requirements.

11.Click Dialing Properties and review your dialing settings. If you are required to dial 9 to get an outside line, type 9 in the local and long distance boxes. If you have call waiting service, disable it to prevent it from interrupting a data or fax transmission. When finished, click OK to exit the Modems Properties dialog box..

20	MT5634ZPX-PCI

Image 20

Contents Model MT5634ZPX-PCI MT5634ZPX -PCI Record of RevisionsContents Introduction Initial Checklist Common Problems Introduction Limited WarrantyData is being lost Technical SupportIntroduction and Description MT5634ZPX-PCI Features Introduction and DescriptionPeripiheral Component Interconnect PCI FaxSupport/Functions Downstream RatesUpstream Data Rates Optional V.8bis SequenceWhat is in Your Modem Package? Digital Loss and Robbed-bit Signaling Auto AdaptHow to Use This Manual AppendixTypographic Conventions You type thisInstallation Introduction What You’ll NeedInstallation Safety WarningsInstallation Overview Configuring the MultiModem ZPX-PCI Windows 95 Plug and PlayInstalling the MultiModemZPX-PCI With the modem, insert the microphone External ConnectionsPlug the telephone’s line cable into Installing Drivers Verifying ConfigurationPort COM Interrupt Address Speed To Remove Previous Modem from Windows Select Start, Settings, and then Control PanelIs Your MultiModemZPX-PCI Ready for Use? Operating Your MultiModemZPX-PCI Simple OperationSelect Start, Programs, Accessories, and then HyperTerminal Software ConfigurationTesting Data Functions Connect dialog box, click Dialing Properties MultiModemZPX-PCI’s fax capabilities Testing FAX FunctionsClick Start, Programs, Accessories, and then WordPad Testing Voice Function Click Start, Programs, Accessories, and then HyperTerminalMultiModemZPX-PCI’s Speakerphone Test AT+FCLASS=8 AT+VLS=7Configuring Communications Software Installation Remote Configuration Basic ProcedureSetup Changing the Setup PasswordPKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands AT Commands, Result Codes, and S-Registers Communication Standard SettingCarrier Control DialEcho Command Mode Characters DS=n Dial Stored Telephone NumberEcho Online Data Characters Hook ControlMonitor Speaker Volume Monitor Speaker ModeReturn Online to Data Mode Modulation HandshakeSr=n Set Register Value Sr? Read Register ValueResult Code Format Result Code SelectionModem Reset Long Space DisconnectAuto Retrain Data Carrier Detect DCD ControlFn Load Factory Default Settings Communications ModeAsynchronous Communications Mode 22bis Guard Tone ControlSelf-Test Commands View Current ConfigurationStore Current Configuration Select Stored Configuration for Hard Reset\Nn Error Correction Mode Selection \Gn Modem Port Flow Control\Jn Data Buffer Control \Kn Set Break Control\T n Inactivity Timer \V n Protocol Result Code\X n XON/XOFF Pass-Through Data Calling ToneSpeaker Codec Loopback Enable Synchronous Buffered ModeAllowed value Registers Decimal Disables, 1-255 enables Modulation 50-150Tones Minute 255Connect. Where K56flex provided =V.90/56Kflex disabledData mode = disable 1 = enableSets one of three 56K operating S36=5,7 LAPM, MNP, or Async MNP or Async1-4 sets the value to Result Codes Connected at 46000 bps Connected at 48000 bpsConnected at 50000 bps Connected at 52000 bpsTroubleshooting Initial Checklist Common Problems TroubleshootingMT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Online Warranty Registration Warranty, Service, and Tech SupportTechnical Support Recording Modem InformationService Multi-Tech Systems, Inc Woodale Drive Mounds View, MNMulti-Tech BBS To log on to the Multi-Tech BBSTo Download a file If you know the file nameIf you don’t know the file name About the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe Appendix Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionMulti-Tech Systems, Inc Fax Branding StatementAppendix Canadian Limitations Notice Appendix Product Safety Compliance +12 VDC, -12 VDC, +5 VDCFigure A-1. Creepage and Clearance Distances EMC, Safety and Terminal Directive Compliance European Low Voltage DirectiveNew Zealand Modem Warning Notice Appendix B Technical Specifications 14,400, 12,000, 9600, 7200, 4800, 2400,90/K56flex, ITU V.34 extended, V.34, ITU ITU Group 3, T.4, T.30, V.21, V.27terAppendix Fax Carrier Frequencies Hz mark, 1850 Hz space for TransmitConnectors Appendix C Ascii Conversion Chart Code HEX DECAppendix D FLASHWINFlash Upgrade IntroductionMT5634ZPX-PCI Index BBS Enable/disable V25 data calling tone S35 IndexAuto Retrain DataFax-back service , 66 FCC Regulations , 68-81 firmware Fall-forward , 7 fallback , 7, 37 faxTones dialing MT5634ZPX-PCI