Multi-Tech Systems MT5634ZPX-PCI owner manual Product Safety Compliance, +12 VDC, -12 VDC, +5 VDC

Page 72

Owner’s Manual

Product Safety Compliance

Approved for connection to telecommunications system specified in the instructions for use subject to the conditions set out in them.

Warning: Interconnection directly, or by way of other apparatus, of ports marked SAFETY WARNING see instructions for use with ports marked or not so marked may produce hazardous conditions on the network. Advice should be obtained from a competent engineer before such a connection is made.

It is a condition of approval that the power required by the host and the total of all adapter cards installed within the host environment, together with any auxiliary apparatus, does not exceed the power specification as stated in the Technical Reference Material of the host apparatus.

The power requirements for the ZPX are:

Modem operating voltages:	+12 VDC, -12 VDC, +5 VDC
Modem power consumption:	1.2 Watts

In order to maintain the independent approval of this card, it is essential that when other option cards are introduced which use or generate a hazardous voltage, the minimum creepages and clearances specified in the following table are maintained. A hazardous voltage is one which exceeds 42.4 VAC peak or 50 VDC. If you have any doubt, seek advice from a competent engineer before installing other adapters into the host equipment.

The equipment must be installed such that with the exception of connection to the host, clearance and creepage distances shown in the following table are maintained between the card and any other assemblies which use or generate a voltage shown in that table. The larger the distance shown in brackets applies where the local environment within the host is subject to conductive pollution or dry nonconductive pollution, which could become conductive due to condensation. Failure to maintain these minimum distances would invalidate approval.

72	MT5634ZPX-PCI

Image 72

Contents Model MT5634ZPX-PCI MT5634ZPX -PCI Record of RevisionsContents Introduction Initial Checklist Common Problems Introduction Limited WarrantyData is being lost Technical SupportIntroduction and Description MT5634ZPX-PCI Features Introduction and DescriptionPeripiheral Component Interconnect PCI FaxSupport/Functions Downstream RatesUpstream Data Rates Optional V.8bis SequenceWhat is in Your Modem Package? Digital Loss and Robbed-bit Signaling Auto AdaptHow to Use This Manual AppendixTypographic Conventions You type thisInstallation Introduction What You’ll NeedSafety Warnings Installation OverviewInstallation Configuring the MultiModem ZPX-PCI Windows 95 Plug and PlayInstalling the MultiModemZPX-PCI External Connections Plug the telephone’s line cable intoWith the modem, insert the microphone Installing Drivers Verifying ConfigurationPort COM Interrupt Address Speed Select Start, Settings, and then Control Panel Is Your MultiModemZPX-PCI Ready for Use?To Remove Previous Modem from Windows Operating Your MultiModemZPX-PCI Simple OperationSoftware Configuration Testing Data FunctionsSelect Start, Programs, Accessories, and then HyperTerminal Connect dialog box, click Dialing Properties Testing FAX Functions Click Start, Programs, Accessories, and then WordPadMultiModemZPX-PCI’s fax capabilities Testing Voice Function Click Start, Programs, Accessories, and then HyperTerminalMultiModemZPX-PCI’s Speakerphone Test AT+FCLASS=8 AT+VLS=7Configuring Communications Software Installation Remote Configuration Basic ProcedureSetup Changing the Setup PasswordPKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands AT Commands, Result Codes, and S-Registers Communication Standard SettingCarrier Control DialEcho Command Mode Characters DS=n Dial Stored Telephone NumberEcho Online Data Characters Hook ControlMonitor Speaker Volume Monitor Speaker ModeReturn Online to Data Mode Modulation HandshakeSr=n Set Register Value Sr? Read Register ValueResult Code Format Result Code SelectionModem Reset Long Space DisconnectAuto Retrain Data Carrier Detect DCD ControlFn Load Factory Default Settings Communications ModeAsynchronous Communications Mode 22bis Guard Tone ControlSelf-Test Commands View Current ConfigurationStore Current Configuration Select Stored Configuration for Hard Reset\Nn Error Correction Mode Selection \Gn Modem Port Flow Control\Jn Data Buffer Control \Kn Set Break Control\T n Inactivity Timer \V n Protocol Result Code\X n XON/XOFF Pass-Through Data Calling ToneEnable Synchronous Buffered Mode Allowed valueSpeaker Codec Loopback Registers Decimal Disables, 1-255 enables Modulation 50-150Tones Minute 255Connect. Where K56flex provided =V.90/56Kflex disabledData mode = disable 1 = enableS36=5,7 LAPM, MNP, or Async MNP or Async 1-4 sets the value toSets one of three 56K operating Result Codes Connected at 46000 bps Connected at 48000 bpsConnected at 50000 bps Connected at 52000 bpsTroubleshooting Initial Checklist Common Problems TroubleshootingMT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Online Warranty Registration Warranty, Service, and Tech SupportTechnical Support Recording Modem InformationService Multi-Tech Systems, Inc Woodale Drive Mounds View, MNMulti-Tech BBS To log on to the Multi-Tech BBSTo Download a file If you know the file nameIf you don’t know the file name About the Multi-Tech Fax-Back Service About CompuServeAbout the Internet Appendix Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionFax Branding Statement AppendixMulti-Tech Systems, Inc Canadian Limitations Notice Appendix Product Safety Compliance +12 VDC, -12 VDC, +5 VDCFigure A-1. Creepage and Clearance Distances EMC, Safety and Terminal Directive Compliance European Low Voltage DirectiveNew Zealand Modem Warning Notice Appendix B Technical Specifications 14,400, 12,000, 9600, 7200, 4800, 2400,90/K56flex, ITU V.34 extended, V.34, ITU ITU Group 3, T.4, T.30, V.21, V.27terAppendix Fax Carrier Frequencies Hz mark, 1850 Hz space for TransmitConnectors Appendix C Ascii Conversion Chart Code HEX DECAppendix D FLASHWINFlash Upgrade IntroductionMT5634ZPX-PCI Index BBS Enable/disable V25 data calling tone S35 IndexAuto Retrain DataFax-back service , 66 FCC Regulations , 68-81 firmware Fall-forward , 7 fallback , 7, 37 faxTones dialing MT5634ZPX-PCI