Multi-Tech Systems MT5634ZPX-PCI owner manual Result Codes

Page 49

3 AT Commands, Result Codes, and S-Registers

Result Codes

In command mode the MultiModemZPX-PCI sends result codes to your computer to provide you with ongoing information during dialing and connection. The following table shows the available result codes.

Terse	Verbose	Description
0	OK	Command executed
1	CONNECT	Modem connected to line
2	RING	Ring signal detected
3	NO CARRIER	Carrier signal lost or not
	detected
4	ERROR	Invalid command
5 *	CONNECT 1200	Connected at 1200 bps
6	NO DIALTONE	No dial tone detected
7	BUSY	Busy signal detected
8	NO ANSWER	No answer at remote end
10*	CONNECT 2400	Connected at 2400 bps
11*	CONNECT 4800	Connected at 4800 bps
12*	CONNECT 9600	Connected at 9600 bps
13*	CONNECT 14400	Connected at 14400 bps
14*	CONNECT 19200	Connected at 19200 bps
24*	CONNECT 7200	Connected at 7200 bps
25*	CONNECT 12000	Connected at 12000 bps
26*	CONNECT 16800	Connected at 16800 bps
40*	CONNECT 300	Connected at 300 bps
55*	CONNECT 21600	Connected at 21600 bps
56*	CONNECT 24000	Connected at 24000 bps
57*	CONNECT 26400	Connected at 26400 bps
58*	CONNECT 28800	Connected at 28800 bps
59*	CONNECT 31200	Connected at 31200 bps
70*	CONNECT 32000	Connected at 32000 bps
60*	CONNECT 33600	Connected at 33600 bps
71*	CONNECT 34000	Connected at 34000 bps
72*	CONNECT 36000	Connected at 36000 bps
73*	CONNECT 38000	Connected at 38000 bps
74*	CONNECT 40000	Connected at 40000 bps
75*	CONNECT 42000	Connected at 42000 bps
76*	CONNECT 44000	Connected at 44000 bps

MT5634ZPX-PCI

49

Image 49

Contents Model MT5634ZPX-PCI Record of Revisions MT5634ZPX -PCIContents Introduction Limited Warranty Introduction Initial Checklist Common ProblemsData is being lost Technical SupportIntroduction and Description MT5634ZPX-PCI Introduction and Description FeaturesFax Peripiheral Component Interconnect PCIDownstream Rates Support/FunctionsUpstream Data Rates Optional V.8bis SequenceDigital Loss and Robbed-bit Signaling Auto Adapt What is in Your Modem Package?Appendix How to Use This ManualYou type this Typographic ConventionsInstallation What You’ll Need IntroductionInstallation Overview Safety WarningsInstallation Windows 95 Plug and Play Configuring the MultiModem ZPX-PCIInstalling the MultiModemZPX-PCI Plug the telephone’s line cable into External ConnectionsWith the modem, insert the microphone Verifying Configuration Installing DriversPort COM Interrupt Address Speed Is Your MultiModemZPX-PCI Ready for Use? Select Start, Settings, and then Control PanelTo Remove Previous Modem from Windows Simple Operation Operating Your MultiModemZPX-PCITesting Data Functions Software ConfigurationSelect Start, Programs, Accessories, and then HyperTerminal Connect dialog box, click Dialing Properties Click Start, Programs, Accessories, and then WordPad Testing FAX FunctionsMultiModemZPX-PCI’s fax capabilities Click Start, Programs, Accessories, and then HyperTerminal Testing Voice FunctionAT+FCLASS=8 AT+VLS=7 MultiModemZPX-PCI’s Speakerphone TestConfiguring Communications Software Installation Basic Procedure Remote ConfigurationChanging the Setup Password SetupPKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands Communication Standard Setting AT Commands, Result Codes, and S-RegistersCarrier Control DialDS=n Dial Stored Telephone Number Echo Command Mode CharactersEcho Online Data Characters Hook ControlMonitor Speaker Mode Monitor Speaker VolumeReturn Online to Data Mode Modulation HandshakeSr? Read Register Value Sr=n Set Register ValueResult Code Format Result Code SelectionLong Space Disconnect Modem ResetAuto Retrain Data Carrier Detect DCD ControlCommunications Mode Fn Load Factory Default SettingsAsynchronous Communications Mode 22bis Guard Tone ControlView Current Configuration Self-Test CommandsStore Current Configuration Select Stored Configuration for Hard Reset\Gn Modem Port Flow Control \Nn Error Correction Mode Selection\Jn Data Buffer Control \Kn Set Break Control\V n Protocol Result Code \T n Inactivity Timer\X n XON/XOFF Pass-Through Data Calling ToneAllowed value Enable Synchronous Buffered ModeSpeaker Codec Loopback Registers 50-150 Decimal Disables, 1-255 enables ModulationTones Minute 255=V.90/56Kflex disabled Connect. Where K56flex providedData mode = disable 1 = enable1-4 sets the value to S36=5,7 LAPM, MNP, or Async MNP or AsyncSets one of three 56K operating Result Codes Connected at 48000 bps Connected at 46000 bpsConnected at 50000 bps Connected at 52000 bpsTroubleshooting Initial Checklist Troubleshooting Common ProblemsMT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Warranty, Service, and Tech Support Online Warranty RegistrationRecording Modem Information Technical SupportMulti-Tech Systems, Inc Woodale Drive Mounds View, MN ServiceTo log on to the Multi-Tech BBS Multi-Tech BBSTo Download a file If you know the file nameIf you don’t know the file name About CompuServe About the Multi-Tech Fax-Back ServiceAbout the Internet Appendix FCC Regulations for Telephone Line Interconnection Appendix a Regulatory ComplianceAppendix Fax Branding StatementMulti-Tech Systems, Inc Canadian Limitations Notice Appendix +12 VDC, -12 VDC, +5 VDC Product Safety ComplianceFigure A-1. Creepage and Clearance Distances European Low Voltage Directive EMC, Safety and Terminal Directive ComplianceNew Zealand Modem Warning Notice 14,400, 12,000, 9600, 7200, 4800, 2400, Appendix B Technical Specifications90/K56flex, ITU V.34 extended, V.34, ITU ITU Group 3, T.4, T.30, V.21, V.27terAppendix Hz mark, 1850 Hz space for Transmit Fax Carrier FrequenciesConnectors Code HEX DEC Appendix C Ascii Conversion ChartIntroduction Appendix D FLASHWINFlash UpgradeMT5634ZPX-PCI Index BBS Index Enable/disable V25 data calling tone S35Auto Retrain DataFall-forward , 7 fallback , 7, 37 fax Fax-back service , 66 FCC Regulations , 68-81 firmwareTones dialing MT5634ZPX-PCI