Multi-Tech Systems MT5634ZPX-PCI Connected at 46000 bps, Connected at 48000 bps, Number, 100, 101

Page 50

Owner’s Manual

Terse	Verbose	Description
77*	CONNECT 46000	Connected at 46000 bps
78*	CONNECT 48000	Connected at 48000 bps
79*	CONNECT 50000	Connected at 50000 bps
80*	CONNECT 52000	Connected at 52000 bps
81*	CONNECT 54000	Connected at 54000 bps
82*	CONNECT 56000	Connected at 56000 bps
88	DELAYED	Delay is in effect for the dialed
		number
89	BLACKLISTED	Dialed number is blacklisted
90	BLACKLIST FULL	Blacklist is full
100	CONNECT 28000	Connected at 28000 bps
101	CONNECT 29333	Connected at 29333 bps
102	CONNECT 30666	Connected at 30666 bps
103	CONNECT 33333	Connected at 33333 bps
104	CONNECT 34666	Connected at 34666 bps
105	CONNECT 37333	Connected at 37333 bps
106	CONNECT 38666	Connected at 38666 bps
107	CONNECT 41333	Connected at 41333 bps
108	CONNECT 42666	Connected at 42666 bps
109	CONNECT 45333	Connected at 45333 bps
110	CONNECT 46666	Connected at 46666 bps
111	CONNECT 49333	Connected at 49333 bps
112	CONNECT 50666	Connected at 50666 bps
113	CONNECT 53333	Connected at 53333 bps
114	CONNECT 54666	Connected at 54666 bps

*EC is added to these Result Codes when the extended Result Codes configuration option is enabled. EC is replaced by one of the following codes, depending on the type of error control connection: V42bis (V.42 error control [LAP-M] and V.42bis data compression); V42 (V.42 error control [LAP-M] only); MNP5 (MNP 4 error control and MNP 5 data compression); MNP4 (MNP 4 error control only); NoEC (No error control protocol).

50	MT5634ZPX-PCI

Image 50

Contents Model MT5634ZPX-PCI MT5634ZPX -PCI Record of RevisionsContents Data is being lost Introduction Initial Checklist Common ProblemsIntroduction Limited Warranty Technical SupportIntroduction and Description MT5634ZPX-PCI Features Introduction and DescriptionPeripiheral Component Interconnect PCI FaxUpstream Data Rates Support/FunctionsDownstream Rates Optional V.8bis SequenceWhat is in Your Modem Package? Digital Loss and Robbed-bit Signaling Auto AdaptHow to Use This Manual AppendixTypographic Conventions You type thisInstallation Introduction What You’ll NeedInstallation Safety WarningsInstallation Overview Configuring the MultiModem ZPX-PCI Windows 95 Plug and PlayInstalling the MultiModemZPX-PCI With the modem, insert the microphone External ConnectionsPlug the telephone’s line cable into Installing Drivers Verifying ConfigurationPort COM Interrupt Address Speed To Remove Previous Modem from Windows Select Start, Settings, and then Control PanelIs Your MultiModemZPX-PCI Ready for Use? Operating Your MultiModemZPX-PCI Simple OperationSelect Start, Programs, Accessories, and then HyperTerminal Software ConfigurationTesting Data Functions Connect dialog box, click Dialing Properties MultiModemZPX-PCI’s fax capabilities Testing FAX FunctionsClick Start, Programs, Accessories, and then WordPad Testing Voice Function Click Start, Programs, Accessories, and then HyperTerminalMultiModemZPX-PCI’s Speakerphone Test AT+FCLASS=8 AT+VLS=7Configuring Communications Software Installation Remote Configuration Basic ProcedureSetup Changing the Setup PasswordPKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands Carrier Control AT Commands, Result Codes, and S-RegistersCommunication Standard Setting DialEcho Online Data Characters Echo Command Mode CharactersDS=n Dial Stored Telephone Number Hook ControlReturn Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Modulation HandshakeResult Code Format Sr=n Set Register ValueSr? Read Register Value Result Code SelectionAuto Retrain Modem ResetLong Space Disconnect Data Carrier Detect DCD ControlAsynchronous Communications Mode Fn Load Factory Default SettingsCommunications Mode 22bis Guard Tone ControlStore Current Configuration Self-Test CommandsView Current Configuration Select Stored Configuration for Hard Reset\Jn Data Buffer Control \Nn Error Correction Mode Selection\Gn Modem Port Flow Control \Kn Set Break Control\X n XON/XOFF Pass-Through \T n Inactivity Timer\V n Protocol Result Code Data Calling ToneSpeaker Codec Loopback Enable Synchronous Buffered ModeAllowed value Registers Tones Decimal Disables, 1-255 enables Modulation50-150 Minute 255Data mode Connect. Where K56flex provided=V.90/56Kflex disabled = disable 1 = enableSets one of three 56K operating S36=5,7 LAPM, MNP, or Async MNP or Async1-4 sets the value to Result Codes Connected at 50000 bps Connected at 46000 bpsConnected at 48000 bps Connected at 52000 bpsTroubleshooting Initial Checklist Common Problems TroubleshootingMT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Online Warranty Registration Warranty, Service, and Tech SupportTechnical Support Recording Modem InformationService Multi-Tech Systems, Inc Woodale Drive Mounds View, MNTo Download a file Multi-Tech BBSTo log on to the Multi-Tech BBS If you know the file nameIf you don’t know the file name About the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe Appendix Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionMulti-Tech Systems, Inc Fax Branding StatementAppendix Canadian Limitations Notice Appendix Product Safety Compliance +12 VDC, -12 VDC, +5 VDCFigure A-1. Creepage and Clearance Distances EMC, Safety and Terminal Directive Compliance European Low Voltage DirectiveNew Zealand Modem Warning Notice 90/K56flex, ITU V.34 extended, V.34, ITU Appendix B Technical Specifications14,400, 12,000, 9600, 7200, 4800, 2400, ITU Group 3, T.4, T.30, V.21, V.27terAppendix Fax Carrier Frequencies Hz mark, 1850 Hz space for TransmitConnectors Appendix C Ascii Conversion Chart Code HEX DECAppendix D FLASHWINFlash Upgrade IntroductionMT5634ZPX-PCI Index BBS Auto Retrain Enable/disable V25 data calling tone S35Index DataFax-back service , 66 FCC Regulations , 68-81 firmware Fall-forward , 7 fallback , 7, 37 faxTones dialing MT5634ZPX-PCI