Multi-Tech Systems MT5634ZPX-PCI owner manual Testing Voice Function

Page 26

Owner’s Manual

Other Ways to Access Microsoft Fax

In Windows 95, select File, Print and select Microsoft Fax as the default printer.

In a Windows 95 application, select File and then Send.

In Microsoft Exchange, select Composeand then New Fax.

Testing Voice Function

There are several tests you can perform to verify the MultiModemZPX- PCI’s voice circuits. Try the answering machine test first. If that doesn’t work and you have a microphone and speaker connected to the MultiModemZPX-PCI, try the loopback and speakerphone tests, which can test the modem’s voice circuits without special software.

MultiModemZPX-PCI’s Answering Machine Test

Test the MultiModemZPX-PCI’s voice function by using the included software to set up the MultiModemZPX-PCI as a telephone answering machine. Have a friend call and leave a message; then play it back.

Loopback Testing

1.Connect a microphone and speaker to the MultiModemZPX-PCI. To avoid feedback, make sure the microphone and speaker are not placed too close to each other. For best results, use a headphone instead of a speaker. If using a headphone, be sure to reduce the headphone volume (if available) before starting.

2.Click Start, Programs, Accessories, and then HyperTerminal.

3.Double-click the Multi-Tech BBS. HyperTerminal starts with the Connect dialog box open.

4.Click Cancel in the Connect dialog box.

26

MT5634ZPX-PCI

Image 26
Contents Model MT5634ZPX-PCI MT5634ZPX -PCI Record of RevisionsContents Data is being lost Introduction Initial Checklist Common ProblemsIntroduction Limited Warranty Technical SupportIntroduction and Description MT5634ZPX-PCI Features Introduction and DescriptionPeripiheral Component Interconnect PCI FaxUpstream Data Rates Support/FunctionsDownstream Rates Optional V.8bis SequenceWhat is in Your Modem Package? Digital Loss and Robbed-bit Signaling Auto AdaptHow to Use This Manual AppendixTypographic Conventions You type thisInstallation Introduction What You’ll NeedInstallation Safety WarningsInstallation Overview Configuring the MultiModem ZPX-PCI Windows 95 Plug and PlayInstalling the MultiModemZPX-PCI With the modem, insert the microphone External ConnectionsPlug the telephone’s line cable into Installing Drivers Verifying ConfigurationPort COM Interrupt Address Speed To Remove Previous Modem from Windows Select Start, Settings, and then Control PanelIs Your MultiModemZPX-PCI Ready for Use? Operating Your MultiModemZPX-PCI Simple OperationSelect Start, Programs, Accessories, and then HyperTerminal Software ConfigurationTesting Data Functions Connect dialog box, click Dialing Properties MultiModemZPX-PCI’s fax capabilities Testing FAX FunctionsClick Start, Programs, Accessories, and then WordPad Testing Voice Function Click Start, Programs, Accessories, and then HyperTerminalMultiModemZPX-PCI’s Speakerphone Test AT+FCLASS=8 AT+VLS=7Configuring Communications Software Installation Remote Configuration Basic ProcedureSetup Changing the Setup PasswordPKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands Carrier Control AT Commands, Result Codes, and S-RegistersCommunication Standard Setting DialEcho Online Data Characters Echo Command Mode CharactersDS=n Dial Stored Telephone Number Hook ControlReturn Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Modulation HandshakeResult Code Format Sr=n Set Register ValueSr? Read Register Value Result Code SelectionAuto Retrain Modem ResetLong Space Disconnect Data Carrier Detect DCD ControlAsynchronous Communications Mode Fn Load Factory Default SettingsCommunications Mode 22bis Guard Tone ControlStore Current Configuration Self-Test CommandsView Current Configuration Select Stored Configuration for Hard Reset\Jn Data Buffer Control \Nn Error Correction Mode Selection\Gn Modem Port Flow Control \Kn Set Break Control\X n XON/XOFF Pass-Through \T n Inactivity Timer\V n Protocol Result Code Data Calling ToneSpeaker Codec Loopback Enable Synchronous Buffered ModeAllowed value Registers Tones Decimal Disables, 1-255 enables Modulation50-150 Minute 255Data mode Connect. Where K56flex provided=V.90/56Kflex disabled = disable 1 = enableSets one of three 56K operating S36=5,7 LAPM, MNP, or Async MNP or Async1-4 sets the value to Result Codes Connected at 50000 bps Connected at 46000 bpsConnected at 48000 bps Connected at 52000 bpsTroubleshooting Initial Checklist Common Problems TroubleshootingMT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Online Warranty Registration Warranty, Service, and Tech SupportTechnical Support Recording Modem InformationService Multi-Tech Systems, Inc Woodale Drive Mounds View, MNTo Download a file Multi-Tech BBSTo log on to the Multi-Tech BBS If you know the file nameIf you don’t know the file name About the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe Appendix Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionMulti-Tech Systems, Inc Fax Branding StatementAppendix Canadian Limitations Notice Appendix Product Safety Compliance +12 VDC, -12 VDC, +5 VDCFigure A-1. Creepage and Clearance Distances EMC, Safety and Terminal Directive Compliance European Low Voltage DirectiveNew Zealand Modem Warning Notice 90/K56flex, ITU V.34 extended, V.34, ITU Appendix B Technical Specifications14,400, 12,000, 9600, 7200, 4800, 2400, ITU Group 3, T.4, T.30, V.21, V.27terAppendix Fax Carrier Frequencies Hz mark, 1850 Hz space for TransmitConnectors Appendix C Ascii Conversion Chart Code HEX DECAppendix D FLASHWINFlash Upgrade IntroductionMT5634ZPX-PCI Index BBS Auto Retrain Enable/disable V25 data calling tone S35Index DataFax-back service , 66 FCC Regulations , 68-81 firmware Fall-forward , 7 fallback , 7, 37 faxTones dialing MT5634ZPX-PCI