Multi-Tech Systems MT5634ZPX-PCI owner manual Peripiheral Component Interconnect PCI, Fax

Page 8

Owner’s Manual

FlashROM upgradable

Compatibility with the standard AT command set used by most communication programs

Stores up to two telephone numbers

Fax

Supports V.17, Group 3 fax communication standards, allowing it to communicate with other fax modems as well as with fax machines

Responds to Class 1 and Class 2 fax commands, enabling it to exchange editable and encrypted faxes with other Windows 95 computers

Sends and receives faxes from your computer at 14,400 bps, 9600 bps, 7200 bps, 4800 bps, 2400 bps, or 300 bps

Voice

Full duplex speakerphone support with adjustable speaker volume control; can record and play back answering machine messages using optional microphone and speaker

Remote/local telephone answering machine (TAM) capabilities include voice mail control, record/playback, and call screening

Supports the TIA/EIA IS-101 AT+V voice command set.

Peripiheral Component Interconnect (PCI)

First developed by companies such as IntelTM, AT&TTM and Digital Equipment CorporationTM, the Peripheral Component Interconnect (PCI) bus used by your MT5634ZPX-PCI provides high performance and is easy to use. Because PCI devices contain registers with the device information required for configuration, full auto configuration of PCI Local Bus add-in boards and components is supported. Performance factors include a bus data path of 64 bits, clock speeds of 66 MHz, and bandwidth of 264 Mbs.

8

MT5634ZPX-PCI

Image 8
Contents Model MT5634ZPX-PCI MT5634ZPX -PCI Record of RevisionsContents Introduction Initial Checklist Common Problems Introduction Limited WarrantyData is being lost Technical SupportIntroduction and Description MT5634ZPX-PCI Features Introduction and DescriptionPeripiheral Component Interconnect PCI FaxSupport/Functions Downstream RatesUpstream Data Rates Optional V.8bis SequenceWhat is in Your Modem Package? Digital Loss and Robbed-bit Signaling Auto AdaptHow to Use This Manual AppendixTypographic Conventions You type thisInstallation Introduction What You’ll NeedInstallation Safety WarningsInstallation Overview Configuring the MultiModem ZPX-PCI Windows 95 Plug and PlayInstalling the MultiModemZPX-PCI With the modem, insert the microphone External ConnectionsPlug the telephone’s line cable into Installing Drivers Verifying ConfigurationPort COM Interrupt Address Speed To Remove Previous Modem from Windows Select Start, Settings, and then Control PanelIs Your MultiModemZPX-PCI Ready for Use? Operating Your MultiModemZPX-PCI Simple OperationSelect Start, Programs, Accessories, and then HyperTerminal Software ConfigurationTesting Data Functions Connect dialog box, click Dialing Properties MultiModemZPX-PCI’s fax capabilities Testing FAX FunctionsClick Start, Programs, Accessories, and then WordPad Testing Voice Function Click Start, Programs, Accessories, and then HyperTerminalMultiModemZPX-PCI’s Speakerphone Test AT+FCLASS=8 AT+VLS=7Configuring Communications Software Installation Remote Configuration Basic ProcedureSetup Changing the Setup PasswordPKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands AT Commands, Result Codes, and S-Registers Communication Standard SettingCarrier Control DialEcho Command Mode Characters DS=n Dial Stored Telephone NumberEcho Online Data Characters Hook ControlMonitor Speaker Volume Monitor Speaker ModeReturn Online to Data Mode Modulation HandshakeSr=n Set Register Value Sr? Read Register ValueResult Code Format Result Code SelectionModem Reset Long Space DisconnectAuto Retrain Data Carrier Detect DCD ControlFn Load Factory Default Settings Communications ModeAsynchronous Communications Mode 22bis Guard Tone ControlSelf-Test Commands View Current ConfigurationStore Current Configuration Select Stored Configuration for Hard Reset\Nn Error Correction Mode Selection \Gn Modem Port Flow Control\Jn Data Buffer Control \Kn Set Break Control\T n Inactivity Timer \V n Protocol Result Code\X n XON/XOFF Pass-Through Data Calling ToneSpeaker Codec Loopback Enable Synchronous Buffered ModeAllowed value Registers Decimal Disables, 1-255 enables Modulation 50-150Tones Minute 255Connect. Where K56flex provided =V.90/56Kflex disabledData mode = disable 1 = enableSets one of three 56K operating S36=5,7 LAPM, MNP, or Async MNP or Async1-4 sets the value to Result Codes Connected at 46000 bps Connected at 48000 bpsConnected at 50000 bps Connected at 52000 bpsTroubleshooting Initial Checklist Common Problems TroubleshootingMT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Online Warranty Registration Warranty, Service, and Tech SupportTechnical Support Recording Modem InformationService Multi-Tech Systems, Inc Woodale Drive Mounds View, MNMulti-Tech BBS To log on to the Multi-Tech BBSTo Download a file If you know the file nameIf you don’t know the file name About the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe Appendix Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionMulti-Tech Systems, Inc Fax Branding StatementAppendix Canadian Limitations Notice Appendix Product Safety Compliance +12 VDC, -12 VDC, +5 VDCFigure A-1. Creepage and Clearance Distances EMC, Safety and Terminal Directive Compliance European Low Voltage DirectiveNew Zealand Modem Warning Notice Appendix B Technical Specifications 14,400, 12,000, 9600, 7200, 4800, 2400,90/K56flex, ITU V.34 extended, V.34, ITU ITU Group 3, T.4, T.30, V.21, V.27terAppendix Fax Carrier Frequencies Hz mark, 1850 Hz space for TransmitConnectors Appendix C Ascii Conversion Chart Code HEX DECAppendix D FLASHWINFlash Upgrade IntroductionMT5634ZPX-PCI Index BBS Enable/disable V25 data calling tone S35 IndexAuto Retrain DataFax-back service , 66 FCC Regulations , 68-81 firmware Fall-forward , 7 fallback , 7, 37 faxTones dialing MT5634ZPX-PCI