Multi-Tech Systems MT5634ZPX-PCI owner manual Gn Modem Port Flow Control, Jn Data Buffer Control

Page 42

Owner’s Manual

Command:

\Gn

Modem Port Flow Control

Values:

 

n = 0

Default:

 

0

Description:

\G0

Returns an OK for backward compatibility with some

 

 

software.

 

\G1

Not supported—responds ERROR.

Command:

\Jn

Data Buffer Control

Values:

 

n = 0

Default:

 

0

Description:

\J0

Enable data buffer—serial port speed is independent of

 

 

connect speed.

 

\J1

Not supported—responds ERROR.

Command:

\Kn

Set Break Control

Values:

 

n = 5

Default:

 

5

Description:

\K5

Modem sends break signal received from the DTE to the

 

 

remote modem.

Command:

\Nn

Error Correction Mode Selection

Values:

 

n = 0–5, or 7

Default:

 

3

Description:

\N0

Non-error correction mode with data buffering

 

 

(same as &Q6).

 

\N1

Direct mode.

 

\N2

MNP reliable mode.

 

\N3

V.42/MNP auto-reliable mode.

 

\N4

V.42 reliable mode.

 

\N5

V.42, MNP, or non-error correction (same as \N3).

 

\N7

V.42, MNP, or non-error correction (same as \N3).

Command:

\Qn

Local Flow Control Selection

Values:

 

n = 0, 1, or 3

Default:

 

3

Description:

\Q0

Disable flow control (same as &K0).

 

\Q1

XON/XOFF software flow control (same as &K4).

 

\Q2

CTS-only flow control. Not supported—responds ERROR.

 

\Q3

RTS/CTS hardware flow control (same as &K3).

42

MT5634ZPX-PCI

Image 42
Contents Model MT5634ZPX-PCI MT5634ZPX -PCI Record of RevisionsContents Data is being lost Introduction Initial Checklist Common ProblemsIntroduction Limited Warranty Technical SupportIntroduction and Description MT5634ZPX-PCI Features Introduction and DescriptionPeripiheral Component Interconnect PCI FaxUpstream Data Rates Support/FunctionsDownstream Rates Optional V.8bis SequenceWhat is in Your Modem Package? Digital Loss and Robbed-bit Signaling Auto AdaptHow to Use This Manual AppendixTypographic Conventions You type thisInstallation Introduction What You’ll NeedSafety Warnings Installation OverviewInstallation Configuring the MultiModem ZPX-PCI Windows 95 Plug and PlayInstalling the MultiModemZPX-PCI External Connections Plug the telephone’s line cable intoWith the modem, insert the microphone Installing Drivers Verifying ConfigurationPort COM Interrupt Address Speed Select Start, Settings, and then Control Panel Is Your MultiModemZPX-PCI Ready for Use?To Remove Previous Modem from Windows Operating Your MultiModemZPX-PCI Simple OperationSoftware Configuration Testing Data FunctionsSelect Start, Programs, Accessories, and then HyperTerminal Connect dialog box, click Dialing Properties Testing FAX Functions Click Start, Programs, Accessories, and then WordPadMultiModemZPX-PCI’s fax capabilities Testing Voice Function Click Start, Programs, Accessories, and then HyperTerminalMultiModemZPX-PCI’s Speakerphone Test AT+FCLASS=8 AT+VLS=7Configuring Communications Software Installation Remote Configuration Basic ProcedureSetup Changing the Setup PasswordPKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands Carrier Control AT Commands, Result Codes, and S-RegistersCommunication Standard Setting DialEcho Online Data Characters Echo Command Mode CharactersDS=n Dial Stored Telephone Number Hook ControlReturn Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Modulation HandshakeResult Code Format Sr=n Set Register ValueSr? Read Register Value Result Code SelectionAuto Retrain Modem ResetLong Space Disconnect Data Carrier Detect DCD ControlAsynchronous Communications Mode Fn Load Factory Default SettingsCommunications Mode 22bis Guard Tone ControlStore Current Configuration Self-Test CommandsView Current Configuration Select Stored Configuration for Hard Reset\Jn Data Buffer Control \Nn Error Correction Mode Selection\Gn Modem Port Flow Control \Kn Set Break Control\X n XON/XOFF Pass-Through \T n Inactivity Timer\V n Protocol Result Code Data Calling ToneEnable Synchronous Buffered Mode Allowed valueSpeaker Codec Loopback Registers Tones Decimal Disables, 1-255 enables Modulation50-150 Minute 255Data mode Connect. Where K56flex provided=V.90/56Kflex disabled = disable 1 = enableS36=5,7 LAPM, MNP, or Async MNP or Async 1-4 sets the value toSets one of three 56K operating Result Codes Connected at 50000 bps Connected at 46000 bpsConnected at 48000 bps Connected at 52000 bpsTroubleshooting Initial Checklist Common Problems TroubleshootingMT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Online Warranty Registration Warranty, Service, and Tech SupportTechnical Support Recording Modem InformationService Multi-Tech Systems, Inc Woodale Drive Mounds View, MNTo Download a file Multi-Tech BBSTo log on to the Multi-Tech BBS If you know the file nameIf you don’t know the file name About the Multi-Tech Fax-Back Service About CompuServeAbout the Internet Appendix Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionFax Branding Statement AppendixMulti-Tech Systems, Inc Canadian Limitations Notice Appendix Product Safety Compliance +12 VDC, -12 VDC, +5 VDCFigure A-1. Creepage and Clearance Distances EMC, Safety and Terminal Directive Compliance European Low Voltage DirectiveNew Zealand Modem Warning Notice 90/K56flex, ITU V.34 extended, V.34, ITU Appendix B Technical Specifications14,400, 12,000, 9600, 7200, 4800, 2400, ITU Group 3, T.4, T.30, V.21, V.27terAppendix Fax Carrier Frequencies Hz mark, 1850 Hz space for TransmitConnectors Appendix C Ascii Conversion Chart Code HEX DECAppendix D FLASHWINFlash Upgrade IntroductionMT5634ZPX-PCI Index BBS Auto Retrain Enable/disable V25 data calling tone S35Index DataFax-back service , 66 FCC Regulations , 68-81 firmware Fall-forward , 7 fallback , 7, 37 faxTones dialing MT5634ZPX-PCI