MGE UPS Systems 66103, 66102 user manual Measurements

Page 40

4.2.6 Measurements

Click on "Measurements" in the menu

◗The next window shows the measurements for a mono phases UPS.

The following measurements are saved and time-stamped (env. 430):

◗"AC Normal : Voltage": Value of the utility voltage supplying the UPS

◗"AC Normal : Frequency": Value of the utility frequency supplying the UPS

◗"AC Output : Voltage": Value of the output voltage of your UPS

◗"AC Output : Frequency": Value of the output frequency of your UPS

◗"AC Output : Power (kVA)": Value of the output power of your UPS

◗"AC Output : Load level (%)": Value of the percentage of load at UPS output

◗"Battery : Capacity (%)": Percentage of charge available in the battery

◗"Battery : Remaining time (mn)": Estimation of the remaining backup time

◗The save frequency of these values is defined in the "System" page (60 seconds by default). Approximately 435 time-stamps are stored permanently on the card. The oldest time-stamps are automatically deleted.

◗"Save Log" enables all saved values to be opened or saved in CSV format. (compatible with Excel type spreadsheets)

◗"Clear Log" enables deletion of all records. Enter the login/password to validate this action.

ENERGIZE YOUR ENTERPRISE
Network Management Card – User Manual	34003991EN/DA	Page 40/120

Image 40

Contents Network Management Card 66102 Energize Your EnterpriseContents Server Protection Configuration VIA RS232Industrial Network Management Card Inmc Option Jbus Table AppendicesMGE MIB GlossaryMGE Office Protection Systems Network Solution General PresentationConnecting the UPS to the Ethernet network Protection of the computers/serversSupervision of the UPSs over the network ConnectionHow to connect UPS / agent / network Setting up the protectionPresentation of the Network Management Card NMC Compatibility with UPSsSending text messages SMS Direct sending of E-mailEnvironment Sensor option Technical data Hardware characteristicsConfiguration EMC CompatibilityAdministration NetworkEnvironment sensor List of ports usedMIB Management Information Base BOOTP/DHCP Default parametersMgeups Unpacking and check on contents InstallationIndications LED Installation in the UPSACT Sensor installation option Configure IP parameters ConfigurationMGE UPS Systems Network Management Card Your network is equipped with a Dhcp server Test after configuration Your network is not equipped with a Dhcp serverSupervision and administration by browser Optimising the performance of your browserUPS UPS propertiesUPS zone general information on the UPS 23/120 24/120 25/120 26/120 UPS status zone Essential information Viewing the modules 29/120 Viewing the alarms Alarm table for modular UPS Viewing the About your UPS window On-line help UPS control 35/120 36/120 UPS weekly schedule programming Shutdown parameters For the main outlet Master by default Measurements Event log System log Notification Email Notification44/120 Mail Message Settings 46/120 Configuration Network settings 49/120 System 51/120 Notified Applications 53/120 Central shutdown configuration Access control 55/120TLS Date and time 58/120 Firmware upload Characteristics Environment Sensor optionEnvironment Status Environment Settings Display in the list of current alarms 4 Log Set-up of the shutdown parameters Server protectionShutdown criteria managed by the Network Management Card Utility failure Start of the shutdown sequence Shutdown when backup time is less than Shutdown durationProtection of a server connected to a controlled outlet Controlled outletsLoad shedding or sequential shutdown Different server and UPS shutdown sequences Sequential startup70/120 Shutdown management with 2 NMC boards SettingsShutdown Duration Configuration via RS232 Choice 2 Network Configuration Choice 1 Restart / ResetChoice 1 Read Network settings Choice 2 Modify Network settings Choice 3 Set Ethernet speedChoice 3 Lost password / Set Login Password to Default Choice 4 Return to Default Configuration Presentation Industrial Network Management Card Inmc optionOverview Functions Technical characteristics JBUS/MODBUSInstallation 1 RS232 link configuration and connection2 RS485 link configuration and connection 2.1 RS485 connection81/120 2.2 RS485 link configuration for 2 wires connexion 83/120 2.3 RS485 link configuration for 4 wires connexion 85/120 Configuration of the JBUS/MODBUS communication parameters Choice 1 Display Jbus settings Choice 2 Modify Jbus settingsChoice 4 Reset Jbus diagnostics Choice 3 Display Jbus diagnosticsChoice 5 Return to Jbus Default Configuration Choice 6 Display Jbus frames Additional Web pages Data for Pulsar 700 / 1000 Jbus tableStatus table Measurements table Data for Pulsar M 2200 94/120 Data for Pulsar MX 4000 / 5000 96/120 Data for Pulsar MX frame 15 Modular fault table 99/120 100/120 101/120 Sensor data 5.1 Status table103/120 Read of the personalization table Other data Table of alarms Tables of alarms and eventsAppendices UPS OK Battery fault Battery OK Imminent UPS shutoff Table of UPS events 110/120 Table of system alarms Snmp objects MGE MIB113/120 1yes 2no 1,4,1 Table des Traps MIB Trap116/120 MIB Management Information Base GlossaryNetwork Management Proxy 118/120 NMS Network Management Station Snmp NSM Network Shutdown ModuleSnmp Simple Network Management Protocol Smtp Simple Mail Transfer Protocol120/120