MGE UPS Systems 66102, 66103 user manual Installation in the UPS, Led, Act

Page 15

Ethernet port

LED

Colour

Activity

Description

 

 

 

 

 

ACT

Green

Off

Card not connected to the network.

 

 

 

 

 

 

On

Card connected to the network but

 

 

 

without activity

 

 

 

 

 

 

 

Flashing

Port is active in receiving /

 

 

 

transmission

 

 

 

 

 

 

 

 

 

 

100M

Orange

Off

Port operating at 10Mbits/s.

 

 

 

 

 

 

On

Port operating at 100Mbits/s.

 

 

 

 

 

 

Service port

 

 

 

 

 

 

 

 

LED

Colour

Activity

Description

UPS

Green

Off

Card startup in progress.

 

 

 

 

 

 

On

Communication with UPS in

Data

 

 

progress

 

 

 

 

 

 

 

 

 

 

 

 

 

Normal operation.

 

 

Flashing

 

Communication with the UPS is

 

 

 

 

 

operational

 

 

 

 

 

RS232

Orange

Off

Configuration menu is active

 

 

 

 

 

 

On

Normal operation. Configuration

 

 

 

 

 

menu is deactived

 

 

Flashing

Communication with the

 

 

 

 

 

Environment Sensor (option).

 

 

 

 

 

 

2.3Installation in the UPS

The Network Management Card (66102) can be "hot" installed in all UPSs of the MGE Office Protection Systems range equipped with a Minislot without having to shut it down.

Remove the protective plastic cover from the Minislot

Note the card's MAC address prior to insertion

Insert and tighten the card's retaining screws

Connect the ETHERNET cable

Wait 2 min. the card is completely operational when the green UPS Data LED flashes continuously

ENERGIZE YOUR ENTERPRISE

 

 

Network Management Card – User Manual

34003991EN/DA

Page 15/120

Image 15
Contents Energize Your Enterprise Network Management Card 66102Contents Configuration VIA RS232 Server ProtectionIndustrial Network Management Card Inmc Option Glossary Jbus TableAppendices MGE MIBGeneral Presentation MGE Office Protection Systems Network SolutionProtection of the computers/servers Connecting the UPS to the Ethernet networkConnection Supervision of the UPSs over the networkCompatibility with UPSs How to connect UPS / agent / networkSetting up the protection Presentation of the Network Management Card NMCDirect sending of E-mail Sending text messages SMSEnvironment Sensor option EMC Compatibility Technical dataHardware characteristics ConfigurationList of ports used AdministrationNetwork Environment sensorMIB Management Information Base Default parameters BOOTP/DHCPMgeups Installation Unpacking and check on contentsIndications Installation in the UPS LEDACT Sensor installation option Configuration Configure IP parametersMGE UPS Systems Network Management Card Your network is equipped with a Dhcp server Your network is not equipped with a Dhcp server Test after configurationOptimising the performance of your browser Supervision and administration by browserUPS properties UPSUPS zone general information on the UPS 23/120 24/120 25/120 26/120 UPS status zone Essential information Viewing the modules 29/120 Viewing the alarms Alarm table for modular UPS Viewing the About your UPS window On-line help UPS control 35/120 36/120 UPS weekly schedule programming Shutdown parameters For the main outlet Master by default Measurements Event log System log Email Notification Notification44/120 Mail Message Settings 46/120 Configuration Network settings 49/120 System 51/120 Notified Applications 53/120 Central shutdown configuration 55/120 Access controlTLS Date and time 58/120 Firmware upload Environment Sensor option CharacteristicsEnvironment Status Environment Settings Display in the list of current alarms 4 Log Server protection Set-up of the shutdown parametersShutdown criteria managed by the Network Management Card Utility failure Start of the shutdown sequence Shutdown duration Shutdown when backup time is less thanControlled outlets Protection of a server connected to a controlled outletLoad shedding or sequential shutdown Sequential startup Different server and UPS shutdown sequences70/120 Settings Shutdown management with 2 NMC boardsShutdown Duration Configuration via RS232 Choice 1 Restart / Reset Choice 2 Network ConfigurationChoice 1 Read Network settings Choice 3 Set Ethernet speed Choice 2 Modify Network settingsChoice 3 Lost password / Set Login Password to Default Choice 4 Return to Default Configuration Industrial Network Management Card Inmc option PresentationOverview Functions JBUS/MODBUS Technical characteristics1 RS232 link configuration and connection Installation2.1 RS485 connection 2 RS485 link configuration and connection81/120 2.2 RS485 link configuration for 2 wires connexion 83/120 2.3 RS485 link configuration for 4 wires connexion 85/120 Configuration of the JBUS/MODBUS communication parameters Choice 2 Modify Jbus settings Choice 1 Display Jbus settingsChoice 3 Display Jbus diagnostics Choice 4 Reset Jbus diagnosticsChoice 5 Return to Jbus Default Configuration Choice 6 Display Jbus frames Additional Web pages Jbus table Data for Pulsar 700 / 1000Status table Measurements table Data for Pulsar M 2200 94/120 Data for Pulsar MX 4000 / 5000 96/120 Data for Pulsar MX frame 15 Modular fault table 99/120 100/120 101/120 5.1 Status table Sensor data103/120 Read of the personalization table Other data Tables of alarms and events Table of alarmsAppendices UPS OK Battery fault Battery OK Imminent UPS shutoff Table of UPS events 110/120 Table of system alarms MGE MIB Snmp objects113/120 1yes 2no 1,4,1 MIB Trap Table des Traps116/120 Glossary MIB Management Information BaseNetwork Management Proxy 118/120 Smtp Simple Mail Transfer Protocol NMS Network Management Station SnmpNSM Network Shutdown Module Snmp Simple Network Management Protocol120/120