MGE UPS Systems 66102, 66103 Glossary, MIB Management Information Base, Network Management Proxy

Page 117

9 Glossary

Bootp:

Protocol based on UDP used to allocate an IP address corresponding to an Ethernet card during the startup phase. Defined by the RCF 951

Community name:

Access key to access SNMP agent information

DHCP Dynamic Host Configuration Protocol

This IETF protocol enables remote, automatic, self-configuration of the IP addresses of a workstation.

DNS Domain Name Sevicel

The DNS protocol ensure correspondence between the name of a machine and its IP address

E-mail

Electronic means of transmitting messages and/or files.

Gateway

Interconnection equipment between networks with different conventions, to enable communication between them

HTML

(HyperText Markup Language) Language used to describe hypertext pages on the web.

HTTPS : is the secure version of HTTP, the communication protocol of the World Wide Web. It was invented by Netscape Communications Corporation to provide authentication and encrypted communication and is used in electronic commerce.

IP

Internet Protocol. Network layer protocol in the TCP/IP stack offering a no-connection inter-network service . The IP protocol offers functions for addressing, service type specification, fragmentation and re-assembling and security. Defined in RFC 791.

MIB MANAGEMENT INFORMATION BASE

-Group of software commands to control and administrate a device through the network. Each type of device (server, hub, PC, UPS, etc.) has its own MIB

NETWORK MANAGEMENT CARD

Communication cards to supervise UPS and communicate with Network Shutdown Module to insure power protection on servers

NETWORK MANAGEMENT PROXY

Communication software installed on a PC connected to the UPS to supervise it and communicate with Network Shutdown Module to insure power protection on servers

ENERGIZE YOUR ENTERPRISE
Network Management Card – User Manual	34003991EN/DA	Page 117/120

Image 117

Contents Energize Your Enterprise Network Management Card 66102Contents Configuration VIA RS232 Server ProtectionIndustrial Network Management Card Inmc Option Appendices Jbus TableMGE MIB GlossaryGeneral Presentation MGE Office Protection Systems Network SolutionProtection of the computers/servers Connecting the UPS to the Ethernet networkConnection Supervision of the UPSs over the networkSetting up the protection How to connect UPS / agent / networkPresentation of the Network Management Card NMC Compatibility with UPSsDirect sending of E-mail Sending text messages SMSEnvironment Sensor option Hardware characteristics Technical dataConfiguration EMC CompatibilityNetwork AdministrationEnvironment sensor List of ports usedMIB Management Information Base Default parameters BOOTP/DHCPMgeups Installation Unpacking and check on contentsIndications Installation in the UPS LEDACT Sensor installation option Configuration Configure IP parametersMGE UPS Systems Network Management Card Your network is equipped with a Dhcp server Your network is not equipped with a Dhcp server Test after configurationOptimising the performance of your browser Supervision and administration by browserUPS properties UPSUPS zone general information on the UPS 23/120 24/120 25/120 26/120 UPS status zone Essential information Viewing the modules 29/120 Viewing the alarms Alarm table for modular UPS Viewing the About your UPS window On-line help UPS control 35/120 36/120 UPS weekly schedule programming Shutdown parameters For the main outlet Master by default Measurements Event log System log Email Notification Notification44/120 Mail Message Settings 46/120 Configuration Network settings 49/120 System 51/120 Notified Applications 53/120 Central shutdown configuration 55/120 Access controlTLS Date and time 58/120 Firmware upload Environment Sensor option CharacteristicsEnvironment Status Environment Settings Display in the list of current alarms 4 Log Server protection Set-up of the shutdown parametersShutdown criteria managed by the Network Management Card Utility failure Start of the shutdown sequence Shutdown duration Shutdown when backup time is less thanControlled outlets Protection of a server connected to a controlled outletLoad shedding or sequential shutdown Sequential startup Different server and UPS shutdown sequences70/120 Settings Shutdown management with 2 NMC boardsShutdown Duration Configuration via RS232 Choice 1 Restart / Reset Choice 2 Network ConfigurationChoice 1 Read Network settings Choice 3 Set Ethernet speed Choice 2 Modify Network settingsChoice 3 Lost password / Set Login Password to Default Choice 4 Return to Default Configuration Industrial Network Management Card Inmc option PresentationOverview Functions JBUS/MODBUS Technical characteristics1 RS232 link configuration and connection Installation2.1 RS485 connection 2 RS485 link configuration and connection81/120 2.2 RS485 link configuration for 2 wires connexion 83/120 2.3 RS485 link configuration for 4 wires connexion 85/120 Configuration of the JBUS/MODBUS communication parameters Choice 2 Modify Jbus settings Choice 1 Display Jbus settingsChoice 3 Display Jbus diagnostics Choice 4 Reset Jbus diagnosticsChoice 5 Return to Jbus Default Configuration Choice 6 Display Jbus frames Additional Web pages Jbus table Data for Pulsar 700 / 1000Status table Measurements table Data for Pulsar M 2200 94/120 Data for Pulsar MX 4000 / 5000 96/120 Data for Pulsar MX frame 15 Modular fault table 99/120 100/120 101/120 5.1 Status table Sensor data103/120 Read of the personalization table Other data Tables of alarms and events Table of alarmsAppendices UPS OK Battery fault Battery OK Imminent UPS shutoff Table of UPS events 110/120 Table of system alarms MGE MIB Snmp objects113/120 1yes 2no 1,4,1 MIB Trap Table des Traps116/120 Glossary MIB Management Information BaseNetwork Management Proxy 118/120 NSM Network Shutdown Module NMS Network Management Station SnmpSnmp Simple Network Management Protocol Smtp Simple Mail Transfer Protocol120/120