Lightwave Communications 3200 user manual Modem Command

Page 35

sys admin>>NETWORK B
Enter accepts present value
N-B: Enter IP address	000.000.000.000> 172.16.1.1
N-B: Enter Subnet Mask	255.255.255.255> 255.255.255.0
N-B: Enter Default Gateway address	255.255.255.255> 172.16.1.200
N-B: Enter 2nd Dest. Network	255.255.255.255>
N-B: Enter 2nd Netmask	255.255.255.255>
N-B: Enter 2nd Gateway address	255.255.255.255>
N-B: BOOTP at startup?	Y>

Save changes and update card? Yes or No: No>y

Card installed, settings updated

sys admin>>

When the NETWORK command is used with a card slot letter as a command qualifier, it will attempt to change the parameters only for that card slot. In all other aspects, the command behaves the same as if the /ALL qualifier was used.

If a bootp server is present on the same network as the ConsoleServer 3200 network card and bootp is enabled on the network card, then the network card will use the IP address and subnet mask assigned by the bootp server rather than those assigned by the sys admin.

Once a network card has been assigned an IP address either by a bootp server or by the sys admin, then the ConsoleServer may be accessed by telnet. Connecting to the default telnet port reaches the user login; connecting to port 5000 reaches the sys admin login.

6.6Modem Command

The MODEM command allows manipulation of the modem card initialization string. When the command is entered, the sys admin is prompted for the new initialization string. Typing a new initialization string and pressing <ENTER> will create a new initialization string for the modem, while just pressing <ENTER> will accept the current value. After pressing <ENTER>, the sys admin is asked to confirm the changes to send the string to the modem. Typing YES and <ENTER> will send the initialization string immediately to the modem card, while typing NO and <ENTER> discards the entered initialization string and keeps the old string. If the modem card is not currently installed, the settings are not sent, but are kept in control card memory. The control card will send those settings in memory when a modem card is installed.

31

Image 35

Contents June ConsoleServerPage Page Error! Bookmark not defined Rear View of ConsoleServer Product DescriptionFeatures Interface Security Passwords64K Fifo Audit Trail ConnectionsPage Chassis Power Supply ModuleAccess Cards Terminal Cards System ComponentsModem Card ConsoleServer 3200 Location and Cooling Installation Instructions Items in the Shipping ContainerRack/Desktop Installation Power RequirementsConnecting to the Sys Admin Port Default DIP Switch Settings DCE Connecting Equipment to the ConsoleServerConsoleServer 3200 serial port default settings Network Card RJ45 to RJ45 Cables Device Card typical adapters and 3200 port configurationDevice Card SUNPage ConsoleServer 3200 Adapter Quick Checklist General layout showing terminal port and device port numbers ConsoleServer 3200 Administration Logging In, Serial Connection Serial terminal will display the following text at power-upSystem Help Logging In, Network ConnectionLogging Out Logged in Help Screen Logged OUT Help ScreenLOG /ENABLEDISABLE Changing the Administration Password Creating and Managing Users 6.2.1 Adding a User ID Device Device Device Device Device Device Device Device Listing User IDs Editing a User IDListusers Deleting a User IDDevices Command J K L M N O Terminals CommandD E Network CommandPage Page Modem Command Connections Command Status CommandsKevin Server Version Command Listcards CommandInfo Command LOG Command Powerstatus CommandSys Admin Session Management Commands Breaking User Connections Linesperpage CommandTimeout Command Break CommandTelnettimeout Command Forcelogout CommandSaving and Restoring System Settings Modemtimeout CommandChanging the System Prompt Updating the ConsoleServer 3200 Software User Access and Interface Terminal Card Overview of Commands Bye CommandLogged in Help Logged OUT HelpPrevious Monitor A.K.A. Device Mode HelpF2 PULL-DOWN Menu Showing Initial Menu Choices Logging In and Changing PasswordsConnection Info Screen Checking ConnectionsF2 PULL-DOWN Menu to Select a Device PORT, Part Selecting a Device PortF2 PULL-DOWN Menu to Listen to a Device Port Part Listening to a Server SessionF2 PULL-DOWN Menu to Listen to a Device Port Part Direct Mode Escape Sequence Direct ModeF2 PULL-DOWN Menu for Device A.K.A. Monitor Mode Using the BufferDisplay Previous Goto Beginning of BufferGoto END of Buffer Display NextReverse N Lines Forward N LinesF2 PULL-DOWN Menu to Change Break Sequence Break Generation SequenceF2 PULL-DOWN Menu to Display System Info Displaying System InformationFront Panel Display Information Page Page Page RJ-45 Connector Appendix a Adapter & Connector PinoutsMale Female DB9 Page Requirements Getting Started Communications SettingsUpdate over Direct Serial Connection Update over Network Sys admin tftpkill Ending the Flash Update Slots for programming purposes Environmental Appendix C System Specifications PhysicalAC Power DC PowerModem Interface Terminal and DeviceNetwork Not SupportedAppendix D -DC Power Page Overcurrent Protection DC Supply ConnectorAppendix E Command Abbreviations Terminal, Network, and Modem Commands Abbreviation Character Appendix F Hexadecimal Ascii CodeHexadecimal Equivalent DEL Index See also User