Lightwave Communications 3200 user manual Bye Command, Overview of Commands

Page 48

At power-up, the network card does not respond to network connect requests until the control card has completed its system initialization. Once the power-up sequence is complete, the network card obtains its network parameters from the control card, and is ready to accept connections over the network. It is important to note that the network card does not retain its network parameters (i.e., IP address, subnet mask, gateway address) if moved from one card slot to another. The network parameters remain assigned to a card slot, and will be assigned to whatever network card is in that slot.

7.3Modem Card

The modem card allows users to remotely access the servers attached to the ConsoleServer 3200 via a dial-up connection. The modem automatically detects the connection speed, and allows connections of up to 38.4K baud. The control card must complete its start-up initialization check before a user may access the ConsoleServer 3200 through the modem card.

The modem card must be installed in card slot "A" of the ConsoleServer 3200 chassis. The modem card will not function if it is inserted in any other card slot, nor will any other card type function in slot A. To connect the modem card to the telephone network, insert an ordinary telephone cable (RJ11) in the jack on the modem card, and insert the other end in a telephone network jack, as outlined in section 5.3. See section 6.6 for instructions on setting the modem initialization string.

The user interface for the modem card is identical to that found on the terminal card with the exception of one command, which is outlined below. Only one user at a time may connect to the modem card.

7.3.1 The Bye Command

A user may disconnect from the modem card and automatically log out from the ConsoleServer 3200 by sending the BYE command. This command will work at any login level that the user may send commands to the ConsoleServer 3200 (i.e., logged out, logged in, and monitor mode). When the command is received, the modem card disconnects the telephone connection, and then logs the user out from the ConsoleServer 3200. This command is unique to the modem card user interface.

7.4Overview of Commands

Several levels of access are available to the user, from simple access of the ConsoleServer 3200 to direct access of servers attached to the ConsoleServer 3200. Many of the commands are sensitive to which level the user is in, and not all commands are available at all levels.

The first prompt the user should see after connecting to the ConsoleServer 3200 is the LCI3200> prompt (additional information may be on the screen as indicated in the

44

Page 47 Page 49
Image 48
Page 47 Page 49
Contents ConsoleServer JunePage Page Error! Bookmark not defined Product Description Rear View of ConsoleServerFeatures Security Passwords 64K Fifo Audit TrailConnections InterfacePage Power Supply Module Access Cards Terminal CardsSystem Components ChassisModem Card Installation Instructions Items in the Shipping Container Rack/Desktop InstallationPower Requirements ConsoleServer 3200 Location and CoolingConnecting to the Sys Admin Port Default DIP Switch Settings Connecting Equipment to the ConsoleServer ConsoleServer 3200 serial port default settingsDCE Network Card Device Card typical adapters and 3200 port configuration Device CardSUN RJ45 to RJ45 CablesPage ConsoleServer 3200 Adapter Quick Checklist General layout showing terminal port and device port numbers ConsoleServer 3200 Administration Serial terminal will display the following text at power-up Logging In, Serial ConnectionLogging In, Network Connection Logging OutSystem Help Logged OUT Help Screen Logged in Help ScreenLOG /ENABLEDISABLE Changing the Administration Password Creating and Managing Users 6.2.1 Adding a User ID Device Device Device Device Device Device Device Device Editing a User ID Listing User IDsDeleting a User ID ListusersDevices Command Terminals Command J K L M N ONetwork Command D EPage Page Modem Command Status Commands Connections CommandKevin Server Listcards Command Version CommandInfo Command Powerstatus Command LOG CommandSys Admin Session Management Commands Linesperpage Command Timeout CommandBreak Command Breaking User ConnectionsForcelogout Command Telnettimeout CommandModemtimeout Command Saving and Restoring System SettingsChanging the System Prompt Updating the ConsoleServer 3200 Software User Access and Interface Terminal Card Bye Command Overview of CommandsLogged OUT Help Logged in HelpMonitor A.K.A. Device Mode Help PreviousLogging In and Changing Passwords F2 PULL-DOWN Menu Showing Initial Menu ChoicesChecking Connections Connection Info ScreenSelecting a Device Port F2 PULL-DOWN Menu to Select a Device PORT, PartListening to a Server Session F2 PULL-DOWN Menu to Listen to a Device Port PartF2 PULL-DOWN Menu to Listen to a Device Port Part Direct Mode Direct Mode Escape SequenceUsing the Buffer F2 PULL-DOWN Menu for Device A.K.A. Monitor ModeGoto Beginning of Buffer Goto END of BufferDisplay Next Display PreviousForward N Lines Reverse N LinesBreak Generation Sequence F2 PULL-DOWN Menu to Change Break SequenceDisplaying System Information F2 PULL-DOWN Menu to Display System InfoFront Panel Display Information Page Page Page Appendix a Adapter & Connector Pinouts RJ-45 ConnectorMale Female DB9 Page Requirements Communications Settings Update over Direct Serial ConnectionGetting Started Update over Network Sys admin tftpkill Ending the Flash Update Slots for programming purposes Appendix C System Specifications Physical AC PowerDC Power EnvironmentalInterface Terminal and Device NetworkNot Supported ModemAppendix D -DC Power Page DC Supply Connector Overcurrent ProtectionAppendix E Command Abbreviations Terminal, Network, and Modem Commands Abbreviation Appendix F Hexadecimal Ascii Code Hexadecimal EquivalentCharacter DEL Index See also User
Top Page Image Contents