LevelOne FPS-3001TXU, FPS-2112, FPS-3002USB manual Port Tab, Physical Port, Logical Port

Page 37

Level One Printer Servers

Port Tab

This screen has 2 panels - Physical Port and Logical Port.

Physical Port

The following settings are available:

•Selected Physical Port - Select the Physical Printer Port you wish to configure.

•Handshake Signal - Select Busy Only or Busy & Ack for the Physical Port.

•Printer Type - Select High Speed or Low Speed for the Printer Type.

Logical Port

Logical Ports (printers) can be used in the Unix environment. The following settings are available:

•Selected Logical Port - Select the Logical Printer Port you wish to configure.

•Map to Physical Port - Select the physical Printer Port which the Logical printer will use.

•Convert LF to LF+CR - If checked, LF (line feed) characters are changed to CR+LF (carriage return + line feed).

•Prefix of Job - The printer control string (in hex) to be sent to the printer before each print job. This string cannot exceed 15 characters.

•Suffix of Job - The printer control string (in hex) to be sent to the printer after each print job. This string cannot exceed 15 characters.

Figure 29: Port Screen

The Get Defaults button will reset all settings to their factory-default values.

- 34 -

Image 37

Contents Level One Print Servers Table of Contents Appendix B Windows Server Configuration Appendix a SpecificationsAppendix C Unix Systems Appendix D NetWareIntroduction FeaturesPackage Contents Safety InstructionsPower Green Status Orange Description LED IndicatorsModels FPS-3001TXU 100BaseT Direct AttachFPS-3002USB Power Green Status Red DescriptionStatus Description FPS-2112Green Red To restore the factory default settings Diagnostic Push Buttonfor FPS-3001TXU and FPS-3002USBTo generate a Diagnostic print out Procedure LAN InstallationUsing the Windows Wizard ConfigurationProcedure OverviewLevelOne Printer Server Screen If the desired LevelOne Printer Server is not listedPrinting Methods Client PC ConfigurationWhich printing method should I use? Checking your Network Protocols Windows Network ConfigurationWindows Peer-to-peer Printing Windows 2000/XP SetupChoose Standard TCP/IP Port, then click New Port Ensure the LPR Byte Counting Enabled setting is Enabled PTP Printer Port Setup Windows 9x/ME SetupIf your LevelOne Printer Server is not listed Print Port Setup Peer-to-peer PrintingManagement Configure Printer PortPort Advanced Port OptionsBanner Retry IntervalNetwork Neighborhood Windows SMB PrintingPrinting from MS-DOS Programs Capture Settings Windows 98/MELogin as Administrator Open the command prompt window Capture Settings Windows 2000/XPWindows with Server-based Print Queues When prompted for Network Path or Queue NameAdvanced Setup and Management AppleTalk SetupMacintosh AppleTalk Software RequirementsMacintosh OS LPR printing SetupInstallation BiAdmin Management UtilityRequirements OperationIcons Device Status Device ListPrinter Status Upgrade ConfigurationWizard RefreshDiagnostics menu ConfigurationMenus Main MenuSystem Screen System TabTCP/IP Screen TCP/IP Tab AppleTalk Screen AppleTalk TabNetBEUI Screen NetBEUI TabInternet Printing Screen Internet Printing TabPhysical Port Port TabLogical Port NetWare Tab Preparation Web-Based ManagementConfiguration Screens Connecting to the LevelOne Printer ServerAppleTalk NetBEUI Abort Job if ErrorDomain Name Response TimeConnection General NetWareManagement Stations Snmp Simple Network Management ProtocolOther Screens Configure ServerServer Status Printer PortsInternet Printing Logical PrintersIPP Server Configuration Special FeaturesInternet Printing Protocol IPP Installing from the CD-ROM IPP Client Setup Windows 98/MEInstalling using IPPCLIENT.EXE IPP Client ConfigurationSelect Printer for IPP Port Changing the IPP Port SettingsPort 2 if exists IPP Client Setup Windows 2000/XPUsing IPP Printers System Requirements Internet Mail PrintingMail Server Internet LevelOne Printer ServerInternet Mail Printing Configuration User Software Installation User SoftwarePort Name Remote PrinterChecking the Printer Driver Using the new PortInterNet Printing Progress Printing through the InternetHardware & LAN Problems TroubleshootingProblem No All the LevelOne Printer Servers LEDs are off If using 10/100BaseT, check the HubProblem No My document didnt print to the right printer Problem No Why do I get an incorrect printout?Problem No My file doesnt print with the correct fonts Problem No My EPS file doesnt print with the correct fontsLevel One Printer Servers Windows Printing To remove an existing printer port installationLevel One Printer Servers Problem No Then select File Properties Details Problem No My old printer cannot print or prints garbageLevelOne Printer Server device is not recognized Unix TroubleshootingEnvironmental Specifications SpecificationsFCC Statement CE StandardsACK Parallel Port Pin AssignmentsFPS-3002USB FPS-3002USBFPS-2112 FPS-2112Specifications Feature Table3001TXU 3002USB Windows NT4.0 Server Windows Server ConfigurationAdding TCP/IP Printing Support Adding a TCP/IP Remote PrinterWindows 2000 Message Windows 2000/2003 ServerOther LevelOne Printer Server Configuration LevelOne Printer Server IP Address ConfigurationUnix Systems LPD on IBM AIX LPD PrintingField Entry Action Sample Command ProcedureLPD on System Adding Remote PrintersField Data LPD on LinuxLPD on BSD Printing using LPD NetWare NetWareCreating an Ndps Manager Object At the Identification page, click the Printer Agent List Creating an Ndps Printer AgentConfigure Port Handler NetWare 3 Operation ModeFrame Type NetWare Remote Printer Mode NetWare Print Server ModeDevice Name Print ServerPreparation Using BiAdmin with ClientButtons Print Server Mode BinderyQuickset Button Bindery NetWare Configuration Button BinderyIf you have multiple File Servers File Server If you have a single File ServerPrinter OperatorSelect Printer Port Bindery Printer ButtonAssign Queues Bindery Assigning Printer Queues RequiredTo assign operators to Queues Optional To Assign Users to Queues RequiredNetWare Password Bindery PS Mode PasswordName Print Server Mode NDSQuickset Button NDS NetWare Configuration Button NDSSelect Printer Port NDS To assign operators to the Print Queue Optional Assign Users to Queue NDS PS modeNetWare Password NDS PS Mode Password NDS