Lantronix XPort manual Port Properties, Edit the following fields as necessary

Page 17

3: Getting Started

characters. (An enhanced password setting of 16 characters is available under Security Settings on the Telnet Setup Mode window.)

Note: You do not need a password to access the Setup Mode window via a serial connection.

Port Properties

Click the Port Properties button to display the following page:

Edit the following fields as necessary:

Serial Protocol

RS232

 

Note: RS-232 is the only available option for XPort Device Server

 

versions XP1001000-01 & XP1001000-03. RS-422/485 is an additional

 

option for XP1004000-03 (XPort-485).

Speed

300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, and

 

230400

 

XPort-03 and greater provide high-performance mode that also supports

XPort™ User Guide

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents XPort User Guide Copyright and Trademark Date Rev Comments Disclaimer and RevisionsContents Mail Settings Gpio Interface Chapter Summary Using This GuidePurpose and Audience XPort Integration Guide Additional DocumentationApplications IntroductionCapabilities Addresses and Port Numbers Protocol SupportHardware Address IP AddressAssigning an IP Address Installing DeviceInstaller Using DeviceInstaller to Assign an IP AddressGetting Started Required InformationSelect Assign a specific IP address and click Next Assigning an IP Address Lantronix Web-Manager Using Web-Manager to Configure the UnitUnit Configuration Settings Server Properties Edit the following fields as necessary Port PropertiesDedicated Connection Connect Mode SettingsFlush Mode Input Buffer Packing Algorithm Additional SettingsUpdate Settings Factory SettingsUsing a Telnet Connection Using Setup Mode for ConfigurationAccessing Setup Mode Setup Menu Options Using the Serial PortSetup Mode Configuration Parameters Change Telnet Configuration Password Server Configuration Network ConfigurationSet Gateway IP Address Netmask Number of Bits for Host PartBaudrate Channel 1 Configuration Serial Port ParametersDhcp Name Mode XPort-485 only Interface ModeMode Option Common I/F Mode Setting Binary HexPort Number FlowFlow Control Option Hex Port Numbers Reserved forIncoming Connection Connect ModeConnect Mode Option Response Hostlist Autostart Automatic ConnectionWithout Echo Modem ModeDatagram Type Full Verbose 11. Modem Mode MessagesMessage Meaning 12. Modem Mode Commands Modem Mode Function CommandRemote IP Address Remote PortDisconnect Mode Option Flush Mode Buffer Flushing13. Disconnect Mode Options 14. Flush Mode OptionsOption Pack ControlChannel Port Password DisConnTime Inactivity TimeoutSend Characters Telnet Terminal TypeMail Setup Mail SettingsTrigger Setup Expert SettingsHigh CPU Performance mode ARP Cache timeout in secondsMonitor Mode at Bootup RS-485 TX Enable Active LevelDisable Snmp Security SettingsDisable Telnet Setup Snmp Community NameDisable Port 77FE Hex Disable Tftp Firmware UpgradeDisable Web Server Disable Echo PortsEncryption Tutorial Command syntax telnetEnable Enhanced Password Factory DefaultsDisable Port 77F0 Hex Channel 1 Configuration DefaultsExpert Settings Defaults Exit Configuration ModeSecurity Settings Defaults Mail SettingsFeatures Configurable PinsGpio Interface Control ProtocolGuidelines CommandsByte 0 Command Types Command 11h, Get Directions Command 10h, Get FunctionsCommand 12h, Get Active Levels Command 13h, Get Current StatesExamples Command 1Ah, Set Active LevelsCommand 1Bh, Set States Command details Updating Firmware Using TftpObtaining Firmware Reloading Firmware ROM FileUser Guide Entering Monitor Mode via the Network Port Entering Monitor Mode via the Serial PortMonitor Mode Commands Monitoring the NetworkResponse Meaning Command Command Name FunctionProblem/Message Reason Solution TroubleshootingProblems and Error Messages Caps Lock is not on Address and Network Class Please try againServer, the No Connection With Email eutechsupp@lantronix.com Technical Support
Top Page Image Contents