Lantronix XPort manual Autostart Automatic Connection, Hostlist

Page 30

4: Using Setup Mode for Configuration

Command String Result if remote IP is 129.1.2.3 and remote port is 1234

C0.0.0.0/0

Autostart (Automatic Connection)

Connects to 129.1.28.10, port 12; enters Monitor Mode

If you enable autostart, the unit automatically connects to the remote IP address and remote port specified when the firmware starts.

Hostlist

If you enable this option, the device server scrolls through the

 

hostlist until it connects to a device listed in the hostlist table.

 

Once it connects, the unit stops trying to connect to any others. If

 

this connection fails, the unit continues to scroll through the table

 

until it is able to connect to another IP in the hostlist.

 

Hostlist supports a minimum of 1 and a maximum of 12 entries.

 

Each entry contains the IP address and the port number.

 

The hostlist is disabled for Manual Mode and for Modem Mode.

 

The unit will not accept a data connection from a remote device

 

when the hostlist option is enabled.

Figure 4-7. Hostlist Option

Change Setup:

0 Server configuration

1 Channel 1 configuration

3 E-mail settings

5 Expert settings

6Security

7Factory defaults

8Exit without save

9

Save and exit

Your choice ? 1

 

Baudrate (9600) ?

 

 

I/F

Mode (4C) ?

 

 

Flow (00) ?

 

 

Port No (10001) ?

 

 

ConnectMode (C0) ?25

 

 

Hostlist :

 

 

No Entry !

 

 

Change Hostlist ? (N) Y

 

Port :

01.

IP address : (000) 172.(000) 19.(000) 0.(000) 1

(0)

?23

 

Port :

02.

IP address : (000) 172.(000) 19.(000) 0.(000) 2

(0)

?3001

 

Port :

03.

IP address : (000) 172.(000) 19.(000) 0.(000) 3

(0)

?10001

 

 

04.

IP address : (000) .(000) .(000) .(000)

 

Hostlist :

01.IP : 172.019.000.001 Port : 00023

02.IP : 172.019.000.002 Port : 03001

03.IP : 172.019.000.003 Port : 10001

Change Hostlist ? (N) N

Hostlist Retrycounter (3) ?

Hostlist Retrytimeout (250) ?

DisConnMode (00) ?

FlushMode (00) ?

XPort™ User Guide

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents XPort User Guide Copyright and Trademark Disclaimer and Revisions Date Rev CommentsContents Mail Settings Gpio Interface Using This Guide Purpose and AudienceChapter Summary Additional Documentation XPort Integration GuideIntroduction CapabilitiesApplications Hardware Address Protocol SupportAddresses and Port Numbers IP AddressAssigning an IP Address Getting Started Using DeviceInstaller to Assign an IP AddressInstalling DeviceInstaller Required InformationAssigning an IP Address Select Assign a specific IP address and click NextUsing Web-Manager to Configure the Unit Lantronix Web-ManagerUnit Configuration Settings Server Properties Port Properties Edit the following fields as necessaryConnect Mode Settings Flush Mode Input BufferDedicated Connection Additional Settings Packing AlgorithmFactory Settings Update SettingsUsing Setup Mode for Configuration Accessing Setup ModeUsing a Telnet Connection Using the Serial Port Setup Menu OptionsSetup Mode Configuration Parameters Set Gateway IP Address Server Configuration Network ConfigurationChange Telnet Configuration Password Netmask Number of Bits for Host PartChannel 1 Configuration Serial Port Parameters Dhcp NameBaudrate Mode Option Interface ModeMode XPort-485 only Common I/F Mode Setting Binary HexFlow Control Option Hex FlowPort Number Port Numbers Reserved forConnect Mode Connect Mode OptionIncoming Connection Response Autostart Automatic Connection HostlistModem Mode Datagram TypeWithout Echo 11. Modem Mode Messages Message MeaningFull Verbose Remote IP Address Modem Mode Function Command12. Modem Mode Commands Remote Port13. Disconnect Mode Options Flush Mode Buffer FlushingDisconnect Mode Option 14. Flush Mode OptionsPack Control OptionSend Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal TypeMail Settings Mail SetupExpert Settings Trigger SetupMonitor Mode at Bootup ARP Cache timeout in secondsHigh CPU Performance mode RS-485 TX Enable Active LevelDisable Telnet Setup Security SettingsDisable Snmp Snmp Community NameDisable Web Server Disable Tftp Firmware UpgradeDisable Port 77FE Hex Disable Echo PortsCommand syntax telnet Encryption TutorialDisable Port 77F0 Hex Factory DefaultsEnable Enhanced Password Channel 1 Configuration DefaultsSecurity Settings Defaults Exit Configuration ModeExpert Settings Defaults Mail SettingsGpio Interface Configurable PinsFeatures Control ProtocolCommands Byte 0 Command TypesGuidelines Command 12h, Get Active Levels Command 10h, Get FunctionsCommand 11h, Get Directions Command 13h, Get Current StatesCommand 1Ah, Set Active Levels Command 1Bh, Set StatesExamples Command details Obtaining Firmware Reloading Firmware Using TftpUpdating Firmware ROM FileUser Guide Monitor Mode Commands Entering Monitor Mode via the Serial PortEntering Monitor Mode via the Network Port Monitoring the NetworkCommand Command Name Function Response MeaningTroubleshooting Problems and Error MessagesProblem/Message Reason Solution Address and Network Class Please try again Caps Lock is not onServer, the No Connection With Technical Support Email eutechsupp@lantronix.com

XPort specifications

The Lantronix XPort is a compact and powerful embedded networking module that enables devices to connect to the Internet and communicate over a network. Small in size yet packed with features, the XPort is ideal for applications that require network connectivity without the complexity and cost associated with traditional networking solutions.

One of the standout features of the XPort is its small form factor. Measuring just 1.6 inches by 1.9 inches, it is designed for seamless integration into a variety of devices, making it a popular choice for manufacturers looking to add networking capabilities to their products without occupying much physical space.

The XPort utilizes the robust and widely used TCP/IP protocol stack, allowing it to facilitate reliable data communication over the Internet and other IP networks. This provides developers with a familiar framework for implementing network functionality, while also ensuring compatibility with various networking standards.

Equipped with a built-in web server, the XPort allows for easy configuration and management through a standard web browser. This user-friendly feature enables developers and end users to interact with the device effortlessly, simplifying tasks such as firmware updates and network settings adjustments.

Another key technology employed in the XPort is its serial-to-Ethernet capabilities. This feature converts serial data from devices into network packets, enabling legacy devices that communicate through serial ports to be connected to modern networks. This is particularly beneficial for industries with a significant number of legacy devices still in operation.

The XPort also incorporates security features, including SSL and SSH, which help protect data transmitted over the network. These security measures are essential in today's digital landscape, where data breaches and unauthorized access are growing concerns.

With its low power consumption and versatile applications, the Lantronix XPort is suitable for a variety of IoT applications, including healthcare devices, industrial automation, and smart metering. Its ability to operate in harsh environments enhances its appeal to manufacturers looking to deploy reliable networking solutions.

In summary, the Lantronix XPort offers a blend of compact design, advanced networking capabilities, and essential security features, making it a valuable asset for any project requiring efficient network connectivity. Its compatibility with existing technologies and ease of integration make it an ideal choice for modern IoT applications.
Top Page Image Contents