Lantronix 900-618 manual To configure the xPico’s device server settings, Auto Negotiate

Page 22

4: Configuration Using Web Manager

Auto Negotiate

With this option, the Ethernet port auto-negotiates the speed and duplex with the hardware endpoint to which it is connected. This is the default.

If this option is not selected, the complete the fields that become available:

Speed: The speed of data transmission. The default is 100 Mbps.

Duplex: The direction of data transmission. The default is Full.

3.When you are finished, click the OK button.

4.On the main menu, click Apply Settings.

Server Configuration

The unit’s server values display when you select Server from the main menu. The following sections describe the configurable parameters on the Server Settings page.

Figure 4-4. Server Settings

To configure the xPico’s device server settings:

1.On the main menu, click Server.

2.Configure or modify the following fields:

xPico User Guide

22

Image 22
Contents User Guide Lantronix Corporate Headquarters Technical Support Sales OfficesDisclaimer Table of Contents Configuration via Telnet or Serial Port Setup Mode Setup Mode Advanced Settings Gpio Interface List of Tables List of FiguresPurpose and Audience Using This GuideChapter Summary Additional Documentation XPico Integration GuideCapabilities IntroductionApplications Addresses and Port Numbers Configuration MethodsProtocol Support Hardware AddressIP Address Product Information LabelPort Numbers To install DeviceInstaller Using DeviceInstallerInstalling DeviceInstaller Assigning an IP AddressSelect Assign a specific IP address and click Next Accessing the xPico Using DeviceInstallerTo view the units current settings NameComments Dhcp Device NameGroup Device FamilyPins Firmware UpgradeableSupports Configurable Supports Http SetupConfiguration Using Web Manager Accessing Web-Manager Using DeviceInstaller Network Configuration Web-Manager Login WindowTo assign an IP address automatically Network ModeSelect Obtain IP address automatically Select Use the following IP configuration Static IP Address ConfigurationEthernet Configuration To assign an IP address manuallyTo configure the xPico’s device server settings Auto NegotiateServer Configuration Host List ConfigurationAdvanced To configure the xPico’s host list Channel 1 and 2 ConfigurationRetry Settings Host InformationTo configure the channel’s serial settings Serial SettingsPort Settings ChannelPack Control Flush Input Buffer Serial to NetworkFlush Output Buffer Network to Serial Connection Settings TCPTo configure a channel’s TCP settings At Time of DisconnectTCP Connection Settings Endpoint Configuration Connect Mode Passive ConnectionConnect Mode Active Connection Connect ProtocolDisconnect Mode Connection Settings UDPTo configure a channel’s UDP settings Use Broadcast Datagram ModeDatagram Type Device Address TableConfigurable Pin Functions Configurable Pin SettingsTo configure the xPico’s Configurable Pins Serial Channel 1 Status LED Apply SettingsApply Defaults Serial Channel 2 Status LEDAccessing Setup Mode Configuration via Telnet or Serial Port Setup ModeTelnet Connection Serial Port Connection To establish a Telnet connectionExiting Setup Mode To exit setup modeBootP/DHCP/AutoIP Options Setup Mode Server ConfigurationServer Configuration Option IP AddressNetmask Number of Bits for Host Part Change Telnet/Web-Manager PasswordSet Gateway IP Address Set DNS Server IP AddressDhcp Name Channel 1 Option 1 or Channel 2 Option Setup Mode Channel ConfigurationBaudrate RS232 Interface Mode Settings Interface ModeInterface Mode Options FlowFlow Control Options Connect ModePort Number Reserved Port NumbersIncoming Connection Connect Mode OptionsIncoming Connection ResponseResponse Active StartupManual Connection Manual Connection Address ExampleTo enable the hostlist Hostlist OptionDatagram Type Modem ModeDirected UDP Modem Mode Commands Numeric ResponseShow IP addr after Ring Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Disconnect Mode Options Remote IP AddressFlush Mode Buffer Flushing Pack ControlTrailing Characters Packing IntervalSend Characters Send Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal TypeExpert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds CPU Performance ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberEnable alternate MAC Security Settings OptionTCP Re-Transmission Timeout Ethernet Connection TypeDisable Telnet Setup Disable SnmpSnmp Community Name Disable Web Server Disable Tftp Firmware UpgradeDisable Port 77FE Hex Disable Web SetupEnable Encryption To configure AES encryption on the xPicoDisable Port 77F0 Hex Default Settings OptionEnable Enhanced Password Channel 1 and Channel 2 Configuration DefaultsHostlist retry timeout Expert Settings DefaultsSecurity Settings Defaults Start character for serial channelFeatures Configurable PinsGpio Interface Control Protocol CommandsByte 0 Command Types GuidelinesCommand 12h, Get Active Levels Command 10h, Get FunctionsCommand 11h, Get Directions Command 13h, Get Current StatesCommand 1Bh, Set States Command 19h, Set DirectionsCommand 1Ah, Set Active Levels Command detailsResponse details Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface To download new firmware from a computerUsing Tftp Command Line Interface Tftp WindowTo recover firmware Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsS0, S1,...,Se, Sf Monitor Mode CommandsG0, G1, ....,Ge, Gf ExampleCommand Response Codes Response MeaningTroubleshooting Problems and Error MessagesCaps Lock is not on Lock onTroubleshooting Technical Support US Technical SupportTechnical Support Europe, Middle East, and Africa Conversion Table Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Scientific CalculatorBinary to Hexadecimal Conversions Compliance RoHS Notice