Lantronix 900-618 manual Disclaimer

Page 3

Disclaimer

Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his or her own expense, will be required to take whatever measures may be required to correct the interference.

Note: This product has been designed to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with this guide, may cause harmful interference to radio communications.

Changes or modifications to this device not explicitly approved by Lantronix will void the user's authority to operate this device.

Note: With the purchase of xPico, the OEM agrees to an OEM firmware license agreement that grants the OEM a non-exclusive, royalty-free firmware license to use and distribute the binary firmware image provided, only to the extent necessary to use the xPico hardware. For further details, please see the xPico OEM firmware license agreement.

Revision History

Date

Rev.

Comments

April 2012

A

Initial release for firmware version 6.8.0.0.

 

 

 

January 2013

B

Updated for firmware version 6.8.0.3.

 

 

 

For the latest revision of this product document, please check our online documentation at www.lantronix.com/support/documentation.

xPico User Guide

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents User Guide Technical Support Sales Offices Lantronix Corporate HeadquartersDisclaimer Table of Contents Configuration via Telnet or Serial Port Setup Mode Setup Mode Advanced Settings Gpio Interface List of Figures List of TablesUsing This Guide Purpose and AudienceChapter Summary XPico Integration Guide Additional DocumentationIntroduction CapabilitiesApplications Hardware Address Configuration MethodsProtocol Support Addresses and Port NumbersProduct Information Label IP AddressPort Numbers Assigning an IP Address Using DeviceInstallerInstalling DeviceInstaller To install DeviceInstallerName Accessing the xPico Using DeviceInstallerTo view the units current settings Select Assign a specific IP address and click NextDevice Family Dhcp Device NameGroup CommentsSupports Http Setup Firmware UpgradeableSupports Configurable PinsAccessing Web-Manager Using DeviceInstaller Configuration Using Web ManagerWeb-Manager Login Window Network ConfigurationNetwork Mode To assign an IP address automaticallySelect Obtain IP address automatically To assign an IP address manually Static IP Address ConfigurationEthernet Configuration Select Use the following IP configurationAuto Negotiate To configure the xPico’s device server settingsHost List Configuration Server ConfigurationAdvanced Host Information Channel 1 and 2 ConfigurationRetry Settings To configure the xPico’s host listChannel Serial SettingsPort Settings To configure the channel’s serial settingsFlush Input Buffer Serial to Network Pack ControlAt Time of Disconnect Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialTCP Connection Settings Connect Protocol Connect Mode Passive ConnectionConnect Mode Active Connection Endpoint ConfigurationConnection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Device Address Table Datagram ModeDatagram Type Use BroadcastConfigurable Pin Settings Configurable Pin FunctionsTo configure the xPico’s Configurable Pins Serial Channel 2 Status LED Apply SettingsApply Defaults Serial Channel 1 Status LEDConfiguration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connection Serial Port ConnectionTo exit setup mode Exiting Setup ModeIP Address Setup Mode Server ConfigurationServer Configuration Option BootP/DHCP/AutoIP OptionsSet DNS Server IP Address Change Telnet/Web-Manager PasswordSet Gateway IP Address Netmask Number of Bits for Host PartDhcp Name Setup Mode Channel Configuration Channel 1 Option 1 or Channel 2 OptionBaudrate Flow Interface ModeInterface Mode Options RS232 Interface Mode SettingsReserved Port Numbers Connect ModePort Number Flow Control OptionsResponse Connect Mode OptionsIncoming Connection Incoming ConnectionActive Startup ResponseManual Connection Address Example Manual ConnectionHostlist Option To enable the hostlistModem Mode Datagram TypeDirected UDP Numeric Response Modem Mode CommandsSend the Escape Sequence +++ in Modem Mode Show IP addr after RingAuto Increment Source Port Remote IP Address Disconnect Mode OptionsPack Control Flush Mode Buffer FlushingPacking Interval Trailing CharactersSend Characters Telnet Terminal Type DisConnTime Inactivity TimeoutChannel Port Password Send CharactersSetup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds Http Port Number ARP Cache timeout in secondsDisable Monitor Mode at bootup CPU PerformanceEthernet Connection Type Security Settings OptionTCP Re-Transmission Timeout Enable alternate MACDisable Snmp Disable Telnet SetupSnmp Community Name Disable Web Setup Disable Tftp Firmware UpgradeDisable Port 77FE Hex Disable Web ServerTo configure AES encryption on the xPico Enable EncryptionChannel 1 and Channel 2 Configuration Defaults Default Settings OptionEnable Enhanced Password Disable Port 77F0 HexStart character for serial channel Expert Settings DefaultsSecurity Settings Defaults Hostlist retry timeoutConfigurable Pins FeaturesGpio Interface Guidelines CommandsByte 0 Command Types Control ProtocolCommand 13h, Get Current States Command 10h, Get FunctionsCommand 11h, Get Directions Command 12h, Get Active LevelsCommand details Command 19h, Set DirectionsCommand 1Ah, Set Active Levels Command 1Bh, Set StatesResponse details To download new firmware from a computer Firmware UpgradesUsing Tftp Graphical User Interface Obtaining Firmware Reloading FirmwareTftp Window Using Tftp Command Line InterfaceTo recover firmware Monitor Mode Commands Monitor ModeEntering Monitor Mode Using the Serial Port Entering Monitor Mode Using the Network PortExample Monitor Mode CommandsG0, G1, ....,Ge, Gf S0, S1,...,Se, SfResponse Meaning Command Response CodesProblems and Error Messages TroubleshootingLock on Caps Lock is not onTroubleshooting Technical Support Technical Support USTechnical Support Europe, Middle East, and Africa Scientific Calculator Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Conversion TableBinary to Hexadecimal Conversions RoHS Notice Compliance
Top Page Image Contents