Lantronix 900-618 manual Lantronix Corporate Headquarters, Technical Support Sales Offices

Page 2

Copyright and Trademark

DeviceLinx®, xPico™ and DeviceInstaller™ are trademarks of Lantronix.

Ethernet is a trademark of XEROX Corporation. UNIX is a registered trademark of The Open Group. Windows is a trademark of Microsoft Corp.

Warranty

For details on the Lantronix warranty policy, please go to our Web site at

www.lantronix.com/support/warranty.

Contacts

Lantronix Corporate Headquarters

167 Technology Drive

Irvine, CA 92618, USA

Toll Free: 800-526-8766

Phone: 949-453-3995

Fax: 949-450-7249

Technical Support

Online: www.lantronix.com/support

Sales Offices

For a current list of our domestic and international sales offices, go to the Lantronix web site at www.lantronix.com/about/contact

xPico User Guide

Image 2

Contents User Guide Lantronix Corporate Headquarters Technical Support Sales OfficesDisclaimer Table of Contents Configuration via Telnet or Serial Port Setup Mode Setup Mode Advanced Settings Gpio Interface List of Tables List of FiguresChapter Summary Using This GuidePurpose and Audience Additional Documentation XPico Integration GuideApplications IntroductionCapabilities Addresses and Port Numbers Configuration MethodsProtocol Support Hardware AddressPort Numbers Product Information LabelIP Address To install DeviceInstaller Using DeviceInstallerInstalling DeviceInstaller Assigning an IP AddressSelect Assign a specific IP address and click Next Accessing the xPico Using DeviceInstallerTo view the units current settings NameComments Dhcp Device NameGroup Device FamilyPins Firmware UpgradeableSupports Configurable Supports Http SetupConfiguration Using Web Manager Accessing Web-Manager Using DeviceInstallerNetwork Configuration Web-Manager Login WindowSelect Obtain IP address automatically Network ModeTo assign an IP address automatically Select Use the following IP configuration Static IP Address ConfigurationEthernet Configuration To assign an IP address manuallyTo configure the xPico’s device server settings Auto NegotiateAdvanced Host List ConfigurationServer Configuration To configure the xPico’s host list Channel 1 and 2 ConfigurationRetry Settings Host InformationTo configure the channel’s serial settings Serial SettingsPort Settings ChannelPack Control Flush Input Buffer Serial to NetworkFlush Output Buffer Network to Serial Connection Settings TCPTo configure a channel’s TCP settings At Time of DisconnectTCP Connection Settings Endpoint Configuration Connect Mode Passive ConnectionConnect Mode Active Connection Connect ProtocolTo configure a channel’s UDP settings Connection Settings UDPDisconnect Mode Use Broadcast Datagram ModeDatagram Type Device Address TableTo configure the xPico’s Configurable Pins Configurable Pin SettingsConfigurable Pin Functions Serial Channel 1 Status LED Apply SettingsApply Defaults Serial Channel 2 Status LEDTelnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode Serial Port Connection To establish a Telnet connectionExiting Setup Mode To exit setup modeBootP/DHCP/AutoIP Options Setup Mode Server ConfigurationServer Configuration Option IP AddressNetmask Number of Bits for Host Part Change Telnet/Web-Manager PasswordSet Gateway IP Address Set DNS Server IP AddressDhcp Name Baudrate Setup Mode Channel ConfigurationChannel 1 Option 1 or Channel 2 Option RS232 Interface Mode Settings Interface ModeInterface Mode Options FlowFlow Control Options Connect ModePort Number Reserved Port NumbersIncoming Connection Connect Mode OptionsIncoming Connection ResponseResponse Active StartupManual Connection Manual Connection Address ExampleTo enable the hostlist Hostlist OptionDirected UDP Modem ModeDatagram Type Modem Mode Commands Numeric ResponseAuto Increment Source Port Send the Escape Sequence +++ in Modem ModeShow IP addr after Ring Disconnect Mode Options Remote IP AddressFlush Mode Buffer Flushing Pack ControlSend Characters Packing IntervalTrailing Characters Send Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal TypeTCP Keepalive time in seconds Setup Mode Advanced SettingsExpert Settings Option CPU Performance ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberEnable alternate MAC Security Settings OptionTCP Re-Transmission Timeout Ethernet Connection TypeSnmp Community Name Disable SnmpDisable Telnet Setup Disable Web Server Disable Tftp Firmware UpgradeDisable Port 77FE Hex Disable Web SetupEnable Encryption To configure AES encryption on the xPicoDisable Port 77F0 Hex Default Settings OptionEnable Enhanced Password Channel 1 and Channel 2 Configuration DefaultsHostlist retry timeout Expert Settings DefaultsSecurity Settings Defaults Start character for serial channelGpio Interface Configurable PinsFeatures Control Protocol CommandsByte 0 Command Types GuidelinesCommand 12h, Get Active Levels Command 10h, Get FunctionsCommand 11h, Get Directions Command 13h, Get Current StatesCommand 1Bh, Set States Command 19h, Set DirectionsCommand 1Ah, Set Active Levels Command detailsResponse details Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface To download new firmware from a computerUsing Tftp Command Line Interface Tftp WindowTo recover firmware Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsS0, S1,...,Se, Sf Monitor Mode CommandsG0, G1, ....,Ge, Gf ExampleCommand Response Codes Response MeaningTroubleshooting Problems and Error MessagesCaps Lock is not on Lock onTroubleshooting Technical Support Europe, Middle East, and Africa Technical SupportTechnical Support US Conversion Table Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Scientific CalculatorBinary to Hexadecimal Conversions Compliance RoHS Notice