Lantronix 900-618 manual Binary to Hexadecimal Conversions

Page 78

A: Binary to Hexadecimal Conversions

4. Click Hex. The hexadecimal value displays.

xPico User Guide

Image 78

Contents User Guide Lantronix Corporate Headquarters Technical Support Sales OfficesDisclaimer Table of Contents Configuration via Telnet or Serial Port Setup Mode Setup Mode Advanced Settings Gpio Interface List of Tables List of FiguresUsing This Guide Purpose and AudienceChapter Summary Additional Documentation XPico Integration GuideIntroduction CapabilitiesApplications Addresses and Port Numbers Configuration MethodsProtocol Support Hardware AddressProduct Information Label IP AddressPort Numbers To install DeviceInstaller Using DeviceInstallerInstalling DeviceInstaller Assigning an IP AddressSelect Assign a specific IP address and click Next Accessing the xPico Using DeviceInstallerTo view the units current settings NameComments Dhcp Device NameGroup Device FamilyPins Firmware UpgradeableSupports Configurable Supports Http SetupConfiguration Using Web Manager Accessing Web-Manager Using DeviceInstallerNetwork Configuration Web-Manager Login WindowNetwork Mode To assign an IP address automaticallySelect Obtain IP address automatically Select Use the following IP configuration Static IP Address ConfigurationEthernet Configuration To assign an IP address manuallyTo configure the xPico’s device server settings Auto NegotiateHost List Configuration Server ConfigurationAdvanced To configure the xPico’s host list Channel 1 and 2 ConfigurationRetry Settings Host InformationTo configure the channel’s serial settings Serial SettingsPort Settings ChannelPack Control Flush Input Buffer Serial to NetworkFlush Output Buffer Network to Serial Connection Settings TCPTo configure a channel’s TCP settings At Time of DisconnectTCP Connection Settings Endpoint Configuration Connect Mode Passive ConnectionConnect Mode Active Connection Connect ProtocolConnection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Use Broadcast Datagram ModeDatagram Type Device Address TableConfigurable Pin Settings Configurable Pin FunctionsTo configure the xPico’s Configurable Pins Serial Channel 1 Status LED Apply SettingsApply Defaults Serial Channel 2 Status LEDConfiguration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection Serial Port Connection To establish a Telnet connectionExiting Setup Mode To exit setup modeBootP/DHCP/AutoIP Options Setup Mode Server ConfigurationServer Configuration Option IP AddressNetmask Number of Bits for Host Part Change Telnet/Web-Manager PasswordSet Gateway IP Address Set DNS Server IP AddressDhcp Name Setup Mode Channel Configuration Channel 1 Option 1 or Channel 2 OptionBaudrate RS232 Interface Mode Settings Interface ModeInterface Mode Options FlowFlow Control Options Connect ModePort Number Reserved Port NumbersIncoming Connection Connect Mode OptionsIncoming Connection ResponseResponse Active StartupManual Connection Manual Connection Address ExampleTo enable the hostlist Hostlist OptionModem Mode Datagram TypeDirected UDP Modem Mode Commands Numeric ResponseSend the Escape Sequence +++ in Modem Mode Show IP addr after RingAuto Increment Source Port Disconnect Mode Options Remote IP AddressFlush Mode Buffer Flushing Pack ControlPacking Interval Trailing CharactersSend Characters Send Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal TypeSetup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds CPU Performance ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberEnable alternate MAC Security Settings OptionTCP Re-Transmission Timeout Ethernet Connection TypeDisable Snmp Disable Telnet SetupSnmp Community Name Disable Web Server Disable Tftp Firmware UpgradeDisable Port 77FE Hex Disable Web SetupEnable Encryption To configure AES encryption on the xPicoDisable Port 77F0 Hex Default Settings OptionEnable Enhanced Password Channel 1 and Channel 2 Configuration DefaultsHostlist retry timeout Expert Settings DefaultsSecurity Settings Defaults Start character for serial channelConfigurable Pins FeaturesGpio Interface Control Protocol CommandsByte 0 Command Types GuidelinesCommand 12h, Get Active Levels Command 10h, Get FunctionsCommand 11h, Get Directions Command 13h, Get Current StatesCommand 1Bh, Set States Command 19h, Set DirectionsCommand 1Ah, Set Active Levels Command detailsResponse details Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface To download new firmware from a computerUsing Tftp Command Line Interface Tftp WindowTo recover firmware Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsS0, S1,...,Se, Sf Monitor Mode CommandsG0, G1, ....,Ge, Gf ExampleCommand Response Codes Response MeaningTroubleshooting Problems and Error MessagesCaps Lock is not on Lock onTroubleshooting Technical Support Technical Support USTechnical Support Europe, Middle East, and Africa Conversion Table Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Scientific CalculatorBinary to Hexadecimal Conversions Compliance RoHS Notice