Lantronix 900-618 manual Command Response Codes, Response Meaning

Page 72

11: Monitor Mode

Table 11-2. Command Response Codes

Response	Meaning
0>	OK; no error

1>	No answer from remote device

2>	Cannot reach remote device or no answer

8>	Wrong parameter(s)

9>	Invalid command

xPico User Guide

Image 72

Contents User Guide Lantronix Corporate Headquarters Technical Support Sales OfficesDisclaimer Table of Contents Configuration via Telnet or Serial Port Setup Mode Setup Mode Advanced Settings Gpio Interface List of Tables List of FiguresUsing This Guide Purpose and AudienceChapter Summary Additional Documentation XPico Integration GuideIntroduction CapabilitiesApplications Configuration Methods Protocol SupportAddresses and Port Numbers Hardware AddressProduct Information Label IP AddressPort Numbers Using DeviceInstaller Installing DeviceInstallerTo install DeviceInstaller Assigning an IP AddressAccessing the xPico Using DeviceInstaller To view the units current settingsSelect Assign a specific IP address and click Next NameDhcp Device Name GroupComments Device FamilyFirmware Upgradeable Supports ConfigurablePins Supports Http SetupConfiguration Using Web Manager Accessing Web-Manager Using DeviceInstallerNetwork Configuration Web-Manager Login WindowNetwork Mode To assign an IP address automaticallySelect Obtain IP address automatically Static IP Address Configuration Ethernet ConfigurationSelect Use the following IP configuration To assign an IP address manuallyTo configure the xPico’s device server settings Auto NegotiateHost List Configuration Server ConfigurationAdvanced Channel 1 and 2 Configuration Retry SettingsTo configure the xPico’s host list Host InformationSerial Settings Port SettingsTo configure the channel’s serial settings ChannelPack Control Flush Input Buffer Serial to NetworkConnection Settings TCP To configure a channel’s TCP settingsFlush Output Buffer Network to Serial At Time of DisconnectTCP Connection Settings Connect Mode Passive Connection Connect Mode Active ConnectionEndpoint Configuration Connect ProtocolConnection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Datagram Mode Datagram TypeUse Broadcast Device Address TableConfigurable Pin Settings Configurable Pin FunctionsTo configure the xPico’s Configurable Pins Apply Settings Apply DefaultsSerial Channel 1 Status LED Serial Channel 2 Status LEDConfiguration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection Serial Port Connection To establish a Telnet connectionExiting Setup Mode To exit setup modeSetup Mode Server Configuration Server Configuration OptionBootP/DHCP/AutoIP Options IP AddressChange Telnet/Web-Manager Password Set Gateway IP AddressNetmask Number of Bits for Host Part Set DNS Server IP AddressDhcp Name Setup Mode Channel Configuration Channel 1 Option 1 or Channel 2 OptionBaudrate Interface Mode Interface Mode OptionsRS232 Interface Mode Settings FlowConnect Mode Port NumberFlow Control Options Reserved Port NumbersConnect Mode Options Incoming ConnectionIncoming Connection ResponseResponse Active StartupManual Connection Manual Connection Address ExampleTo enable the hostlist Hostlist OptionModem Mode Datagram TypeDirected UDP Modem Mode Commands Numeric ResponseSend the Escape Sequence +++ in Modem Mode Show IP addr after RingAuto Increment Source Port Disconnect Mode Options Remote IP AddressFlush Mode Buffer Flushing Pack ControlPacking Interval Trailing CharactersSend Characters DisConnTime Inactivity Timeout Channel Port PasswordSend Characters Telnet Terminal TypeSetup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds ARP Cache timeout in seconds Disable Monitor Mode at bootupCPU Performance Http Port NumberSecurity Settings Option TCP Re-Transmission TimeoutEnable alternate MAC Ethernet Connection TypeDisable Snmp Disable Telnet SetupSnmp Community Name Disable Tftp Firmware Upgrade Disable Port 77FE HexDisable Web Server Disable Web SetupEnable Encryption To configure AES encryption on the xPicoDefault Settings Option Enable Enhanced PasswordDisable Port 77F0 Hex Channel 1 and Channel 2 Configuration DefaultsExpert Settings Defaults Security Settings DefaultsHostlist retry timeout Start character for serial channelConfigurable Pins FeaturesGpio Interface Commands Byte 0 Command TypesControl Protocol GuidelinesCommand 10h, Get Functions Command 11h, Get DirectionsCommand 12h, Get Active Levels Command 13h, Get Current StatesCommand 19h, Set Directions Command 1Ah, Set Active LevelsCommand 1Bh, Set States Command detailsResponse details Firmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware To download new firmware from a computerUsing Tftp Command Line Interface Tftp Window To recover firmware Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port Monitor Mode CommandsMonitor Mode Commands G0, G1, ....,Ge, GfS0, S1,...,Se, Sf ExampleCommand Response Codes Response MeaningTroubleshooting Problems and Error MessagesCaps Lock is not on Lock onTroubleshooting Technical Support Technical Support USTechnical Support Europe, Middle East, and Africa Binary to Hexadecimal Conversions Converting Binary to HexadecimalConversion Table Scientific CalculatorBinary to Hexadecimal Conversions Compliance RoHS Notice