GE QS24 UR quick start UR Switch Module Ethernet Communications, GE Multilin

Page 1

GE Consumer & Industrial

Multilin

UR Switch Module

Ethernet Communications

Switch

Quickstart Guide

Firmware Revision 3.x

Manual P/N: 1601-9042-A1

Manual Order Code: GEK- 113423

Copyright © 2008 GE Multilin

		T	E
	IS		E	R
	G			R
R	E			E
R	E			D

ISO9001:2000

G E

M

U

		IN
	L
I
LT

GE Multilin

215 Anderson Avenue, Markham, Ontario

Canada L6E 1B3

Tel: (905) 294-6222 Fax: (905) 201-2098

Internet: http://www.GEmultilin.com

GE Multilin's Quality

Management System is

registered to ISO9001:2000

QMI # 005094

UL # E83849

1601-0220-A1

Image 1

Contents GE Multilin UR Switch Module Ethernet CommunicationsGE Multilin Incorporated. All rights reserved Table of Contents Table of Contents TOC-2 QS-1 Fiber Twisted Pair copper cableStar Architecture QS.1.2 Supported Network TopologiesMesh Architecture Ring ArchitectureEthernet Unshielded Twisted Pair Unshielded Twisted Pair cableQS-5 QS-6 Wavelengths of light QS.3.1 Fiber Optic EthernetMulti Mode Fiber Cable Cross Section and Physical SpecificationsSingle Mode QS.3.2 Single and Multi-mode cableDifference between Single-mode and Multi-mode Cable QS.3.3 Optical Power BudgetFigure QS-4 Common Fiber Optic Connectors QS.3.4 Maximum fiber segment length calculation Maximum 10 Mbps Ethernet Segment Lengths QS.3.5 UR-2S and UR-2T 10/100 BaseT Switch PortsQS.4 Introduction to the 2S and 2T UR Managed Switch Modules Figure QS-5 Traditional Redundant UR LAN Topology QS.4.1 Hardware Overview QS.4.2 2S and 2T LED indicatorsT60 Transformer Management Relay QS.4.3 Hardware InstallationAC or DC QS.4.4 initial Configuration ProcedureQS-18 DB9 Female to DB9 Female Cable Pin-out QS-20 QS-21 QS-22 QS-23 Type in ipconfig ip= QS-25 Select Properties QS.4.7 Assigning a static IP Address to a personnel computerRight mouse click on the Local Area Connections icon Select Use the following IP address Addresses now being used QS-30 Function Module Offline QS.4.8 Self-test Errors and MeaningEquipment Background QS.5 Tagged VLAN’sConfiguring a Vlan within the Switch QS.5.1 Configuring Tagged VLANsSave We have now configured the Switch to support Tag-based VLANs QS-37 Configure You have now completed the exercise Figure QS-15 Configuration of UR Switch Ring-only Mode QS.5.2 Configuring the UR Switch for Ring Only ModeQS-41 Select Bridge Rstp Then Save Enable Status Once saved, select OK, then OK again to exit Select the Configuration Rstp RO Mode menu as shown above Then Save Enable status For Every Switch RING, Disable LLA on Ports That are Ring Figure QS-16 Configuration of the UR Switch Ring-only mode You have completed configuration of Ring-only modeSaving Switch Settings QS.5.3 Saving and Loading Switch SettingsLoading Switch Settings Select the Retrieve Switch Settings Files optionQS-50 QS.6.2 Selecting the Proper Version QS.6.1 Updating UR Switch Module FirmwareVersion 2.1beta QS-52 QS-53 QS-54