GE QS24 UR quick start QS.4.4 initial Configuration Procedure, AC or DC

Page 21

QUICKSTART GUIDE

AC or DC

 

AC or DC

 

 

NOTE:

HEAVY COPPER CONDUCTOR

 

14 gauge stranded

OR BRAIDED WIRE

 

wire with suitable

 

disconnect devices

 

 

 

 

is recommended

 

 

 

 

 

 

SWITCHGEAR

GROUND BUS

B8b

B8a

B6a

B6b

B5b

 

GND

F

S

-

+

+

-

+

I

U

LOW HIGH

L

T

R

 

 

 

 

 

G

Control Power

Optional UR-2S

E

R

E

 

 

 

 

or UR-2T

 

 

 

 

 

 

 

 

 

 

 

Switch Module

UR SERIES

 

 

 

 

PROTECTION SYSTEM

 

 

FIGURE QS–12: UR Switch Module Wiring Diagram

QS.4.4 initial Configuration Procedure

Ensure Switch is configured before connecting to network devices.

CAUTION

A suitable IP address and subnet mask must be assigned to both the Switch and the UR relay for correct operation. The Switch has been shipped with a default IP address of 192.168.1.2 and a subnet mask of 255.255.255.0. Consult your network administrator to determine if the default IP address, subnet mask or default gateway needs to be modified.

QS.4.5 Configuring the Switch IP Address and Subnet Mask using EnerVista UR Setup Software.

In our example configuration of both the Switch’s IP address and subnet mask must be changed to 3.94.247.229 and 255.255.252.0 respectively. The IP address, subnet mask and default gateway can be configured using either EnerVista UR Setup software, the Switch’s Secure Web Management (SWM), or through the console port using CLI.

In this example EnerVista UR setup software will be used.

ZFrom the Product setup menu select Communications > Ethernet Switch > Configure IP.

ZEnter the Switch’s MAC address (located on the module), IP address that you want to set in the switch, and Subnet Mask.

UR SWITCH MODULE – QUICKSTART GUIDE

QS–17

Image 21
Contents GE Multilin UR Switch Module Ethernet CommunicationsGE Multilin Incorporated. All rights reserved Table of Contents Table of Contents TOC-2 QS-1 Fiber Twisted Pair copper cableStar Architecture QS.1.2 Supported Network TopologiesMesh Architecture Ring ArchitectureEthernet Unshielded Twisted Pair Unshielded Twisted Pair cableQS-5 QS-6 Wavelengths of light QS.3.1 Fiber Optic EthernetMulti Mode Fiber Cable Cross Section and Physical SpecificationsSingle Mode QS.3.2 Single and Multi-mode cableDifference between Single-mode and Multi-mode Cable QS.3.3 Optical Power BudgetFigure QS-4 Common Fiber Optic Connectors QS.3.4 Maximum fiber segment length calculation Maximum 10 Mbps Ethernet Segment Lengths QS.3.5 UR-2S and UR-2T 10/100 BaseT Switch PortsQS.4 Introduction to the 2S and 2T UR Managed Switch Modules Figure QS-5 Traditional Redundant UR LAN Topology QS.4.1 Hardware Overview QS.4.2 2S and 2T LED indicatorsT60 Transformer Management Relay QS.4.3 Hardware InstallationAC or DC QS.4.4 initial Configuration ProcedureQS-18 DB9 Female to DB9 Female Cable Pin-out QS-20 QS-21 QS-22 QS-23 Type in ipconfig ip= QS-25 Select Properties QS.4.7 Assigning a static IP Address to a personnel computerRight mouse click on the Local Area Connections icon Select Use the following IP address Addresses now being used QS-30 Function Module Offline QS.4.8 Self-test Errors and MeaningEquipment Background QS.5 Tagged VLAN’sConfiguring a Vlan within the Switch QS.5.1 Configuring Tagged VLANsSave We have now configured the Switch to support Tag-based VLANs QS-37 Configure You have now completed the exercise Figure QS-15 Configuration of UR Switch Ring-only Mode QS.5.2 Configuring the UR Switch for Ring Only ModeQS-41 Select Bridge Rstp Then Save Enable Status Once saved, select OK, then OK again to exit Select the Configuration Rstp RO Mode menu as shown above Then Save Enable status For Every Switch RING, Disable LLA on Ports That are Ring Figure QS-16 Configuration of the UR Switch Ring-only mode You have completed configuration of Ring-only modeSaving Switch Settings QS.5.3 Saving and Loading Switch SettingsLoading Switch Settings Select the Retrieve Switch Settings Files optionQS-50 QS.6.1 Updating UR Switch Module Firmware QS.6.2 Selecting the Proper VersionVersion 2.1beta QS-52 QS-53 QS-54