Foundry Networks LS 648 Fiber Optic Modules, Power Supplies, Optional Redundant Power Supply

Page 15

Table 2.5: Port Status LEDs

Product Overview

1. Not currently in use.

Figure 2.10 Module LED

			Link/Activity LED
		Table 2.5: Port Status LEDs

LED	Condition		Status

Link/Activity	On		Port has a valid link at 10 Gbps.

	On/Flashing Green		Flashing indicates activity.

	Off		The link is down.

Fiber Optic Modules

A list of the types of fiber optic modules supported on Layer 2 Compact Switches can be found in “Cable length summary table” on page 2-7

NOTE: Some older SFP modules (mini-GBICs for Gigabit Ethernet ports) have latching mechanisms that are larger than the newer parts. These latches could interfere with one another when inserted side by side into a SuperX module. Avoid using these mini-GBICs side by side in the same module. These older modules are identified by the number PL-XPL-00-S13-22 or PL-XPL-00-L13-23 above the serial number. All newer mini-GBICs do not have this limitation.

Power Supplies

There are two power receptacles on the rear panel of each switch. The standard power receptacle is for the AC power cord. The receptacle labeled “RPS” is for the optional redundant power supply.

Optional Redundant Power Supply

The switch supports an optional redundant power supply (RPS), that can supply power to the switch in the event the internal power supply fails.

Power Supply Receptacles

There are two power receptacles on the rear panel of each switch. The standard power receptacle is for the AC power cord. The receptacle labeled “RPS” is for the optional redundant power supply.

Figure 2.11 Power Supply Receptacles

RPS DC In 12V 13A

100-240V~

50-60Hz 2A

Redundant Power Socket	Power Socket

September 2007

© 2007 Foundry Networks, Inc.

2 - 7

Image 15

Contents FGS Release Foundry FastIron LS Layer 2 Compact SwitchHardware Installation Guide FastIron LS FastIron LSCopyright 2007 Foundry Networks, Inc. All rights reserved CHAPTER INSTALLING A FASTIRON LS SWITCHABOUT THIS GUIDE PRODUCT OVERVIEWC ONNECTING N ETWORK D EVICES AND C HECKING C ONNECTIVITYM AINTAINING THE F AST I RON LS H ARDWARE C HAPTERAPPENDIX A HARDWARE SPECIFICATIONSREGULATORY STATEMENTS W ARNINGS C AUTIONS AND W ARNINGSA PPENDIX B C AUTIONSAudience Chapter About This GuideIntroduction What’s Included in This Edition?Email Access How to Get HelpWarranty Coverage Web AccessTable 2.1 Chapter Contents Hardware FeaturesChapter Product Overview FLS624, FLS648FastIron LS Network Interfaces Control FeaturesReset Button Serial Management Interface Console PortInterface Network InterfacesFastIron LS 10/100/1000BASE-T Ports Table 2.2 Network Interfaces10-GbE CX4 Module 10 Gigabit Ethernet Module SlotsCable Specifications for New Module 10 Gbps CX4 PortsCondition Port, System and Module Status LEDsCX4 Transceiver Infiniband cable Table 2.3 Port Status LEDsSystem LEDs Table 2.4 Status LEDsFiber Optic Modules Power SuppliesOptional Redundant Power Supply Power Supply ReceptaclesSeptember Chapter Installing a FastIron LS Switch Unpacking a SystemTable 3.1 Chapter Contents General Requirements Package ContentsFoundry FastIron Configuration Guide Summary of Installation TasksTable 3.2 Summary of Installation Tasks Where to Find More InformationPower Precautions Installation PrecautionsGeneral Precautions Lifting PrecautionsCabling Infrastructure Preparing the Installation SiteInstallation Location Installing the DeviceDesktop Installation Rack Mount InstallationFigure 3.1 Attaching the adhesive feet Wall Mount Installation Figure 3.3 Installing the device in a rackFigure 3.2 Attaching the brackets Package Contents Installing a Redundant Power SupplyAbout the RPS2-EIF Redundant Power Supply Features and BenefitsFastIron RPS2-EIF LEDsPort Indicators System IndicatorsMounting Installing a FastIron LS Redundant Power SupplyEquipment Checklist InstallationDesktop or Shelf Mounting Figure 3.6 Installing the RPS in a RackFigure 3.5 Attaching the brackets FastIron LS648 Connecting Switches to the RPSFLS units GND N.C Installing an Optional Module into the SwitchPorts Pin-Out RPS2-EIF GND N.C RPS Present Status Status Power Good GNDFigure 3.10 Inserting an SFP transceiver into a slot Installing an SFP TransceiverPowering On the System Verifying Proper OperationAttaching a PC or Terminal Null Modem Wiring Map for Serial CableTable 3.3 Serial Cable Wiring Switch’s 9-PinSeptember Step Chapter Connecting Network Devices and Checking ConnectivityAssigning Permanent Passwords Table 4.1 Network Connectivity TasksFLS648 Switchconfig# enable super-user-password text Recovering from a Lost PasswordFLS648 Switch enable FLS648 Switch# configure terminal FLS648 Switchconfig#Devices Running Layer 2 Software Configuring IP AddressesConnecting to Ethernet or Fast Ethernet Hubs Connecting Network DevicesConnectors Cable SpecificationsAutomatic MDI/MDIX Detection Connecting to Workstations, Servers, or RoutersConnecting a Network Device to a Fiber Port Installing a Fiber Optic ModuleCabling a Fiber Optic Module Testing ConnectivityCleaning the Fiber-Optic Connectors Observing LEDsMeaning Troubleshooting Network ConnectionsTable 4.2 Network Connection-Related LED States DesiredFoundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Table 5.1 Chapter Contents Managing FastIron LS Temperature SettingsUsing the Temperature Sensor on the FastIron LS Chapter Maintaining the FastIron LS HardwarePower supply 2 NA - AC - Regular present, status ok Fan 1 failed Displaying the Temperature on the FastIron LSDisplaying Syslog Messages for Temperature on the FastIron LS FLS648 Switch show chassis Power supply 1 not presentFLS648 Switch# show log Changing the Temperature Polling Interval Hardware Maintenance ScheduleInstalling or Replacing a 10-Gigabit Ethernet Module Displaying Management Module CPU UsageInstalling an Optional Module into the Switch Replacing a Fiber Optic ModuleRemoving a 10-Gigabit Ethernet Module Installing a New Fiber Optic Module Removing a Fiber Optic ModuleBail Latch Cleaning the Fiber-Optic Connectors Cabling a Fiber Optic ModuleDigital Optical Monitoring Supported Media Table 5.2 Status Value DescriptionStatus Value CLI Commands no optical-monitor alarm intervalshow optic port/slotnumber September Symptom Chapter TroubleshootingDiagnosing Switch Indicators Table 0.1 Troubleshooting ChartPower and Cooling Problems InstallationIn-Band Access Redundant Power supply specifications Chapter Hardware SpecificationsTable 0.2 Chapter Contents FastIron LS specificationsOperating Environment FastIron LS SpecificationsPhysical Dimensions Environmental ConsiderationsTable 0.7 Storage Environment CoolingStorage Environment Mean Time Before FailureFan Speed Table 0.9 Fan Noise Levels for FastIron LS 24-Port SwitchTable 0.10 Fan Noise Levels for FastIron LS 48-Port Switch Chassis sideTable 0.11 Regulatory Compliance and Safety Approvals Certifications Regulatory ComplianceFCC CFR 47 Part 15 Warning CISPR 22 CLASS A WarningSerial Console Port Pinouts WarrantyPinouts and Signaling VCCICable Type1 Connector TypeLC connector for Table 0.12 Cable length summary tableCable Type Table 0.12 Cable length summary table ContinuedProperty AC Power SupplySpecifications Table 0.13 Specifications for AC PowerPhysical Dimensions and Weight Redundant Power Supply SpecificationsPower Cords Key featuresInput Connector Properties Input ConnectorElectromagnetic Compatibility EMC and Immunity Standards Table 0.15 Input Connector for Power SuppliesTable 0.17 Safety Warning Labels on Power Supplies Safety Agency Approvals and CertificationsSafety Warnings Environmental ConsiderationsTable 0.19 Mean Time Before Failure Specifiations Electrical SpecificationsInput specifications Table 0.20 Input Specifications for Power SuppliesSeptember Europe and Australia Appendix A Regulatory StatementsU.S.A Industry Canada StatementSeptember Cautions Appendix B Cautions and WarningsFoundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Cautions and Warnings CAUTION Never leave tools inside the device Warnings Page Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide