Foundry Networks LS 648 Replacing a Fiber Optic Module, Removing a 10-Gigabit Ethernet Module

Page 47

Installing an Optional Module into the Switch

Maintaining the FastIron LS Hardware

Installing an Optional Module into the Switch

Figure 5.1 Installing the Device in a rack mount

NOTE: The slide-in modules are not hot-swappable, you must power off the switch before installing or removing a module.

To install an optional module into the switch, do the following:

1.Remove the blank metal plate (or a previously installed module) from the appropriate slot by removing the two screws with a flat-head screwdriver.

2.Before opening the package that contains the module, touch the bag to the switch casing to discharge any potential static electricity. Also, it is recommended to use an ESD wrist strap during installation.

3.Remove the module from the anti-static shielded bag.

4.Holding the module level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring that it firmly engages with the connector.

5.If you are sure the module is properly mated with the connector, tighten the retainer screws to secure the module in the slot.

6.When the device is powered on, the Module LED on the switch’s front panel should turn green to confirm that the module is correctly installed and ready to use.

Removing a 10-Gigabit Ethernet Module

1.Remove the 10-Gigabit module:

•Use a #2 Phillips-head screwdriver to loosen and remove the two screws on the 10-Gigabit module.

•Gently lift the module up and out of the device.

2.Place the 10-Gigabit module in an anti-static bag for storage.

3.Do one of the following:

•Insert the new 10-Gigabit module as instructed in the section “Installing an Optional Module into the Switch” on page 5-5.

•If you are removing the module without replacing it, install the blank face place in the rear panel.

Replacing a Fiber Optic Module

You can remove an SFP or XFP from a port and replace it with a new one while the FastIron LS is powered on and running.

This section provides information about the following tasks:

•Removing a fiber optic module

•Installing a new fiber optic module

•Cabling a fiber optic module

September 2007

© 2007 Foundry Networks, Inc.

5 - 5

Image 47

Contents FGS Release Foundry FastIron LS Layer 2 Compact SwitchHardware Installation Guide FastIron LS FastIron LSCopyright 2007 Foundry Networks, Inc. All rights reserved CHAPTER INSTALLING A FASTIRON LS SWITCHABOUT THIS GUIDE PRODUCT OVERVIEWC ONNECTING N ETWORK D EVICES AND C HECKING C ONNECTIVITYM AINTAINING THE F AST I RON LS H ARDWARE C HAPTERREGULATORY STATEMENTS APPENDIX AHARDWARE SPECIFICATIONS W ARNINGS C AUTIONS AND W ARNINGSA PPENDIX B C AUTIONSAudience Chapter About This GuideIntroduction What’s Included in This Edition?Email Access How to Get HelpWarranty Coverage Web AccessTable 2.1 Chapter Contents Hardware FeaturesChapter Product Overview FLS624, FLS648FastIron LS Network Interfaces Control FeaturesReset Button Serial Management Interface Console PortInterface Network InterfacesFastIron LS 10/100/1000BASE-T Ports Table 2.2 Network Interfaces10-GbE CX4 Module 10 Gigabit Ethernet Module SlotsCable Specifications for New Module 10 Gbps CX4 PortsCondition Port, System and Module Status LEDsCX4 Transceiver Infiniband cable Table 2.3 Port Status LEDsSystem LEDs Table 2.4 Status LEDsFiber Optic Modules Power SuppliesOptional Redundant Power Supply Power Supply ReceptaclesSeptember Table 3.1 Chapter Contents Chapter Installing a FastIron LS SwitchUnpacking a System General Requirements Package ContentsFoundry FastIron Configuration Guide Summary of Installation TasksTable 3.2 Summary of Installation Tasks Where to Find More InformationPower Precautions Installation PrecautionsGeneral Precautions Lifting PrecautionsCabling Infrastructure Preparing the Installation SiteInstallation Location Installing the DeviceFigure 3.1 Attaching the adhesive feet Desktop InstallationRack Mount Installation Figure 3.2 Attaching the brackets Wall Mount InstallationFigure 3.3 Installing the device in a rack Package Contents Installing a Redundant Power SupplyAbout the RPS2-EIF Redundant Power Supply Features and BenefitsFastIron RPS2-EIF LEDsPort Indicators System IndicatorsMounting Installing a FastIron LS Redundant Power SupplyEquipment Checklist InstallationFigure 3.5 Attaching the brackets Desktop or Shelf MountingFigure 3.6 Installing the RPS in a Rack FastIron LS648 Connecting Switches to the RPSFLS units GND N.C Installing an Optional Module into the SwitchPorts Pin-Out RPS2-EIF GND N.C RPS Present Status Status Power Good GNDFigure 3.10 Inserting an SFP transceiver into a slot Installing an SFP TransceiverAttaching a PC or Terminal Powering On the SystemVerifying Proper Operation Null Modem Wiring Map for Serial CableTable 3.3 Serial Cable Wiring Switch’s 9-PinSeptember Step Chapter Connecting Network Devices and Checking ConnectivityAssigning Permanent Passwords Table 4.1 Network Connectivity TasksFLS648 Switchconfig# enable super-user-password text Recovering from a Lost PasswordFLS648 Switch enable FLS648 Switch# configure terminal FLS648 Switchconfig#Devices Running Layer 2 Software Configuring IP AddressesConnecting to Ethernet or Fast Ethernet Hubs Connecting Network DevicesConnectors Cable SpecificationsAutomatic MDI/MDIX Detection Connecting to Workstations, Servers, or RoutersConnecting a Network Device to a Fiber Port Installing a Fiber Optic ModuleCabling a Fiber Optic Module Testing ConnectivityCleaning the Fiber-Optic Connectors Observing LEDsMeaning Troubleshooting Network ConnectionsTable 4.2 Network Connection-Related LED States DesiredFoundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Table 5.1 Chapter Contents Managing FastIron LS Temperature SettingsUsing the Temperature Sensor on the FastIron LS Chapter Maintaining the FastIron LS HardwarePower supply 2 NA - AC - Regular present, status ok Fan 1 failed Displaying the Temperature on the FastIron LSDisplaying Syslog Messages for Temperature on the FastIron LS FLS648 Switch show chassis Power supply 1 not presentFLS648 Switch# show log Changing the Temperature Polling Interval Hardware Maintenance ScheduleInstalling or Replacing a 10-Gigabit Ethernet Module Displaying Management Module CPU UsageRemoving a 10-Gigabit Ethernet Module Installing an Optional Module into the SwitchReplacing a Fiber Optic Module Bail Latch Installing a New Fiber Optic ModuleRemoving a Fiber Optic Module Digital Optical Monitoring Cleaning the Fiber-Optic ConnectorsCabling a Fiber Optic Module Status Value Supported MediaTable 5.2 Status Value Description show optic port/slotnumber CLI Commandsno optical-monitor alarm interval September Symptom Chapter TroubleshootingDiagnosing Switch Indicators Table 0.1 Troubleshooting ChartIn-Band Access Power and Cooling ProblemsInstallation Redundant Power supply specifications Chapter Hardware SpecificationsTable 0.2 Chapter Contents FastIron LS specificationsOperating Environment FastIron LS SpecificationsPhysical Dimensions Environmental ConsiderationsTable 0.7 Storage Environment CoolingStorage Environment Mean Time Before FailureFan Speed Table 0.9 Fan Noise Levels for FastIron LS 24-Port SwitchTable 0.10 Fan Noise Levels for FastIron LS 48-Port Switch Chassis sideTable 0.11 Regulatory Compliance and Safety Approvals Certifications Regulatory ComplianceFCC CFR 47 Part 15 Warning CISPR 22 CLASS A WarningSerial Console Port Pinouts WarrantyPinouts and Signaling VCCICable Type1 Connector TypeLC connector for Table 0.12 Cable length summary tableCable Type Table 0.12 Cable length summary table ContinuedProperty AC Power SupplySpecifications Table 0.13 Specifications for AC PowerPhysical Dimensions and Weight Redundant Power Supply SpecificationsPower Cords Key featuresInput Connector Properties Input ConnectorElectromagnetic Compatibility EMC and Immunity Standards Table 0.15 Input Connector for Power SuppliesTable 0.17 Safety Warning Labels on Power Supplies Safety Agency Approvals and CertificationsSafety Warnings Environmental ConsiderationsTable 0.19 Mean Time Before Failure Specifiations Electrical SpecificationsInput specifications Table 0.20 Input Specifications for Power SuppliesSeptember Europe and Australia Appendix A Regulatory StatementsU.S.A Industry Canada StatementSeptember Cautions Appendix B Cautions and WarningsFoundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Cautions and Warnings CAUTION Never leave tools inside the device Warnings Page Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide