Force10 Networks E1200i manual Step CommandTask, Show default-gateway Default-gateway ip-address

Page 84

Step CommandTask (continued)

BOOT_USER # show interface management ethernet

No IP address set for interface management ethernet 0/0!

BOOT_USER # interface management ethernet ip address 1.2.3.4 255.255.0.0 Management ethernet 0/0 IP address: 1.2.3.4 255.255.0.0

BOOT_USER # show interface management ethernet

Management ethernet IP address: 1.2.3.4:ffffff00

BOOT_USER #

8.show default-gateway

default-gateway ip-address

(Optional) Use the show default-gatewaycommand to view gateway information.

If your server is on the same subnet, you do not need to configure a gateway parameter.

If your server is not on the same subnet, use the default-gatewayip-addresscommand to set the gateway IP address.

BOOT_USER # show default-gateway

No gateway IP address specified!

BOOT_USER # default-gateway ip 1.2.3.5

Gateway IP address 1.2.3.5

BOOT_USER # show default-gateway

Gateway IP address: 1.2.3.5

BOOT_USER #

9.dir flash:Use the dir flash: command to list files stored on the internal flash device.

dir slot0:		Use the dir slot0: command to list files stored on the external flash device.
BOOT_USER # dir flash:
Displaying files in flash:			name
size	date	time	name
--------	------	------	--------
11187685	FEB-15-2002	05:37:58	e1200-.bin
11031398	FEB-23-2002	22:42:46	E1200-3.bin
9280984	FEB-17-2002	21:02:36	E1200-2.bin
10778521	FEB-18-2002	22:53:26	E1200-3.1.bin
1787	FEB-23-2002	22:42:46	startup-config

BOOT_USER #

84	System Boot

Image 84

Contents Installing and Maintaining the E1200i System Copyright 2008 Force10 Networks Contents Installing Fan Trays Appendix B System Boot Index List of Figures Page List of Tables Page Defines the information symbols used throughout this guide Symbol DescriptionRelated Publications E1200i System Operating OverviewPage Page RPM Component Minimum Maximum Field-Replaceable Supplying Power DC on Step Task SectionChapter Site Preparation Site Selection CriteriaCabinet Placement PowerRack Mounting Fans and Airflow Storing Components Installing the AC Chassis Unpacking the E1200i AC SystemInstalling the Equipment Rack Shelf Bar To install a equipment rack shelf barStandard Front Chassis Mounting Step TaskInstalling the Chassis into an Equipment Cabinet To install the chassis into a prepared rackInstalling the AC Chassis Installing the DC Chassis Unpacking the E1200i DC SystemInstalling the DC Chassis Rack-Mounting the Chassis Installing the DC Chassis Installing Fan Trays Screw latch Installing Fan Trays To install fan trays Is an illustration of the fan tray safety labelsLabel LocationInstalling Fan Trays Installing AC Power Supplies On/Standby SwitchInstalling Power Supplies Securing the Chassis GroundAC Power Supply and Fan Operability Test Insert power supplyStep Task Status LED isStatus Installing AC Power Supplies Installing DC Power Supplies PEM 0 and PEM 1 Chassis LocationsCable and Connector Requirements Installing DC PEMsUse the following steps to install a DC PEM Over current protector PEM interlock lever Locking screws Cable Connector Required for E1200i DC PEM DC PEM with Connections in Place DC Power Supply and Fan Operability Test Step Task Installing RPMs, Line Cards SFMs Unpacking an RPM or Line CardImportant Points to Remember Installing Line Cards and RPMs RPMsLine Cards Preparing and Installing RPMs and Line Cards Blank PanelsTo install line cards and RPMs Installing an RPM into the E1200iInstalling a Second RPM RPM Label and LEDsDescribes the RPM LED states and the RPM front panel Section Label DescriptionInstalling Switch Fabric Modules SFMs SFM Front Panel and LEDs Illustrates the SFM front panel and LEDsLine Card Cable Management Systems Connecting the Console and Auxiliary Ports RPM Ports and CablesRPM Ports Pin Signal Input/Output Cable and Adapter Pin AssignmentsAccessing the Console with a DB-9 Adapter Accessing the Console with a DB-25 AdapterAccessing the 10/100 Ethernet Management Port Accessing the Auxiliary Port by ModemLabel Description Chapter Powering Up PreparationSupplying Power AC Supplying Power DCBooting to the CLI Prompt Booting from the Bootuser PromptPowering Up Removing and Replacing Components Removing and Replacing Fan TraysRemoving and Replacing AC Power Supplies Removing and Replacing ComponentsInstalling and Maintaining the E1200i System Removing and Replacing DC Power Supplies Remove an AC Power Supply in a non-redundant installationRemove an AC Power Supply in a redundant installation Installing and Maintaining the E1200i System Remove a DC Power Supply Removing and Replacing RPMs, Line Cards, or SFMs Removing and Replacing line cards or RPMsTo remove and replace E1200i line card or RPM modules Removing and Replacing SFMs To remove and replace an SFMNo linecard Removing and Replacing the Air Filter To remove and replace the air filterRemoving and Replacing Components Appendix a Using a Flash Memory Card External Flash Memory Card OverviewInserting the External Flash Memory Card To install the flash memory card Removing the External Flash Memory CardFormatting an External Flash Card To remove the flash memory cardCommand Syntax Command Mode Purpose Copying Files to the External FlashDisplaying Files Stored on the External Flash Page System Boot Process Booting from the Bootuser PromptTo configure the chassis from the Bootuser prompt Step CommandShow boot selector Step Command TaskShow bootvar View the Management interface’s physical settings Auto-negotiationPort Step CommandTask Show default-gateway Default-gateway ip-addressReload System Boot Appendix C Alarms Power Supplies and Alarms SFMs and Alarms Alarms Appendix D System Specifications E1200i AC System Power RequirementsE1200i AC Chassis Physical Design This appendix contains two major sectionsSystem Specifications E1200i DC System Power Requirements E1200i DC Chassis Physical DesignEnvironmental Specifications Operating SpecificationsAgency Compliance Non-operatingSafety Standards and Compliance Agency Certifications Japan Vcci Compliance for Class a EquipmentKorea MIC certification Electromagnetic Emissions ImmunityProduct Recycling and Disposal European Weee symbol System Specifications Appendix E Technical Support This appendix contains these major sectionsAccessing iSupport Services Support Policies section of iSupportOutput from the show tech-supportnon-paged command This Output from the show logging eventlog unit command, whereConsole captures showing the error messages Console captures showing the troubleshooting steps takenRequesting a Hardware Replacement To request replacement hardware, follow these stepsIndex FPC Asic104 Index Installing and Maintaining the E1200i System 105