EverFocus ESM316T002R user manual Lldp Neighbors

Page 34

■LLDP Status - Enable LLDP on the switch. (Default: Disabled)

■Transmission Interval - Configure the periodic transmit interval for LLDP advertisements. (Range: 5-32768 seconds; Default: 30 seconds)

This attribute must comply with the following rule: (Transmission Interval * Transmission Hold Time) ≤ 65536, and Transmission Interval ≥ (4 * Transmission Delay)

■Hold Time Multiplier - Configure the time-to-live (TTL) value sent in LLDP advertisements as shown in the formula below. (Range: 2-10; Default: 3)

The time-to-live tells the receiving LLDP agent how long to retain all information pertaining to the sending LLDP agent if it does not transmit updates in a timely manner. TTL in seconds is based on the following rule: (Transmission Interval * Transmission Hold Time) ≤ 65536. Therefore, the default TTL is 30*3 = 90 seconds.

■Port - Port identifier. (Range: 1-18)

■State - Enable LLDP message transmit and receive modes for LLDP Protocol Data Units. (Options: Disabled, Tx/Rx, Rx only, Tx only; Default: Disabled)

LLDP Neighbors

To display information about devices connected directly to the switch’s ports which are advertising information through LLDP.

Web Smart switch interface

To display LLDP neighbors, click Configuration, LLDP, LLDP Neighbors.

Click the Refresh button to update the LLDP information.

Figure 25: LLDP Neighbors

Hint§

The following parameters are shown on the LLDP Neighbors page.

■Local Port - The local port to which a remote LLDP-capable device is attached.

■Chassis ID - An octet string indicating the specific identifier for the particular chassis in this system.

■TTL - Indicate the time (in seconds) the remote device’s information should be treated as valid.

■LLDP Entry Number - The number of the LLDP table entry.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Gigabit Managed Ethernet Switch 16 PoE+ Ports Content Monitoring About this Guide Introduction Web BrowserLogin Popping Up Window LoggingWeb-Based Management Interface IP Address Setting System InformationIPv6 Address Setting Hint§Port Setting User AccountPort Setting Configuration Trunk Group SettingTrunk Distribution Algorithm Setting Trunk Distribution Algorithm SettingPage Lacp Setting Lacp SettingStatic Vlan Table Setting Static Vlan Table SettingVlan Port Setting Vlan Port SettingVLAN-Stacking Table Setting VLAN-Stacking Table SettingVlan Stacking Setting Vlan Stacking SettingHint§ Igmp Multicast Group Information Multicast Entry TableIgmp Snooping Igmp SnoopingIgmp Global Setting Igmp Vlan Setting Hint§Spanning tree settings Spanning TreePage Spanning Tree Port Setting Spanning tree port settingsPage Quality of Service QoS Port-based Priority SettingDSCP-based Priority Setting DSCP-based Priority SettingPriority to Queue Mapping Setting Priority to Queue Mapping SettingPacket Scheduling Setting Packet Scheduling SettingLldp Configurations Lldp SettingsLldp Neighbors Lldp NeighborsSnmp Setting Trap Receivers Setting Port Mirroring Setting Port mirroringPort Security Setting Port securityPage Bandwidth Control Setting Bandwidth controlPage Jumbo Frame Setting Jumbo Frame SettingManagement Access Filter Management Access FilterPower over Ethernet Setting Power over EthernetSecurity MAC Address InformationStatic MAC Setting Static MAC SettingMAC Filtering Setting 802.1x Setting 802.1x Setting802.1x Port Setting 802.1x Port SettingIP Filter Configurations IP Filter ConfigurationsPage Storm Control settings Storm Control settingsPort Isolation Port IsolationDefence Engine Defence EngineMonitoring Port Statistics InformationHttp Upgrade Http UpgradeReset Factory Defaults ResetReboot Specifications
Top Page Image Contents