Enterasys Networks CM Version 1.0 manual Regulatory Compliance Information

Page 4

Regulatory Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada Notice

This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Class A ITE Notice

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Clase A. Aviso de ITE

ADVERTENCIA: Este es un producto de Clase A. En un ambiente doméstico este producto puede causar interferencia de radio en cuyo caso puede ser requerido tomar medidas adecuadas.

Klasse A ITE Anmerkung

WARNHINWEIS: Dieses Produkt zählt zur Klasse A ( Industriebereich ). In Wohnbereichen kann es hierdurch zu Funkstörungen kommen, daher sollten angemessene Vorkehrungen zum Schutz getroffen werden.

Product Safety

This product complies with the following: UL 60950, CSA C22.2 No. 60950, 2006/95/EC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

Seguridad del Producto

El producto de Enterasys cumple con lo siguiente: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

Produktsicherheit

Dieses Produkt entspricht den folgenden Richtlinien: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10.

ii

Image 4
Contents Enterasys Matrix X Router Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc. Firmware License Agreement Viii Page Page Contents Xii Using This Guide Using the Enterasys Matrix X Router Manual SetWho Should Use This Guide For information about Refer toConventions Used in This Guide Following conventions are used in this guideGetting Help Support@enterasys.comGetting Help Xvi About This Guide DC Power Supply Installation Circuit breaker Overview of the DC Power SupplyEarth ground stud Back View of the DC Power Supply Installation Site Requirements Power Supply Redundancy PlanningPre-Installation Tasks Verify DC Power Compliance of Matrix X ModulesModel Part No Part Number Worksheet DC Compliance of Modules in Existing AC SystemsDC Compliant? Worksheet DC Compliance of Modules for New DC Systems Model Part No Front Panel Serial Number DC Compliant?Minimum Revision of X Modules for DC Power Model Name Minimum 940 Part Number Minimum 940 RevisionUnpacking the DC Power Supply Installing the DC Power Supply Contents of X-DC CartonRemoving Power Supply Vent Plate Installing Power Supply Module Removing Blank Coverplate from Power Supply Slot Power supply slot Power supply coverplateRemoving a Power Supply Removing a Power Supply Removing a Power Supply DC Power Supply Installation Specifications Physical SpecificationsElectrical Specifications SpecificationPower Supply Redundancy Compression LugsModule Power Specifications Redundancy Configurations for DC Power Supply@ 48 VDC ModuleCompliance Standards Regulatory ComplianceRegulatory Compliance Standards